I'm trying to setup an AS5400 for in/out modem/ISDN access, firstly I'd
just like to configure for modem access, but when I dial into it I get
the following output (debug isdn q931, isdn error & spe modem
errors)...The dialing modem just keeps whistling then responds with 'no
carrier'
Jan 3 04:56:56.826 gmt: ISDN Se7/0:15 Q931: RX <- SETUP pd = 8
callref = 0x0001
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Called Party Number i = 0x81, '376800'
Plan:ISDN, Type:Unknown
Jan 3 04:56:56.826 gmt: PM_ST_MODEM_ERR: pm_modem_mgmt_get_modem_parm:
no hwidb/tty
Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> CALL_PROC pd = 8
callref = 0x8001
Channel ID i = 0xA98381
Exclusive, Channel 1
Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> ALERTING pd = 8
callref = 0x8001
Jan 3 04:56:56.834 gmt: ISDN Se7/0:15 Q931: TX -> CONNECT pd = 8
callref = 0x8001
Jan 3 04:56:56.934 gmt: ISDN Se7/0:15 Q931: RX <- CONNECT_ACK pd = 8
callref = 0x0001
****debug waits here for a while, then 'no carrier' on dialing
modem****
Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: RX <- DISCONNECT pd = 8
callref = 0x0001
Cause i = 0x8090 - Normal call clearing
Progress Ind i = 0x8288 - In-band info or appropriate now
available
Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: TX -> RELEASE pd = 8
callref = 0x8001
Jan 3 04:57:52.307 gmt: ISDN Se7/0:15 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x0001
Jan 3 04:57:53.327 gmt:
%MODEMCALLRECORD-6-PM_TERSE_CALL_FAILED_RECORD: DS0
slot/contr/chan=7/0/1, slot/port=1/13, call_id=E, calli
ng=(n/a), called=376800, time=0, finl-state=Half Duplex Train,
disc(modem)=1F06 <unknown>/Requested by host/network indicated discon
nect
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-TRACE_HDR:
Modem 1/13 Events Log:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 1 00:03:47.843 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 1 00:03:47.847 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-CSM_IC_CALLED_NUM:
Jan 3 04:56:56.830 gmt: ISDN incoming called number: 376800
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 3 04:56:56.834 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 3 04:56:56.942 gmt: Port State Reached:
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:56:56.942 gmt: Modem State event:
State: Connect
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:56:59.366 gmt: Modem State event:
State: V.8bis Exchange
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:57:00.638 gmt: Modem State event:
State: Quick Connect
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-CALL_RECORD: ct_hndl=23,
service=None, origin=Answer, category=Modem, DS0 slot/port/ds1/chan=7/
0/0/0, called=376800, calling=(n/a), resource slot/port=1/13,
userid=(n/a), ip=0.0.0.0, mask=0.0.0.0, account id=165, setup=01/03/20
00 04:56:54, conn=0.11, phys=0.00, service=0.00, authen=0.00,
init-rx/tx b-rate=64000/64000, rx/tx chars=0/0, time=55.42, disc subsy
s=ISDN, disc code=0x10, disc text=Normal call clearing
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_CALL_REC: ct_hndl=23, prot:
last=SYNC Mode, attempt=SYNC Mode, comp: last=None, atmp= Non
e, std: last=V.21, attempt=V.21, init=V.21, snr=0, sq=0, rx/tx:
chars=0/0, ec: rx/tx=0/0, rx bad=0, rx/tx b-rate: last=13408/13408,
low=13408/13408, high=300/300, desired-client=(n/a)/(n/a),
desired-host=(n/a)/(n/a), retr: local=0, remote=0, fail=0, speedshift:
lo
cal up/down=0/0, remote up/down=0/0, fail=0, v90: stat=No Attempt,
client=(n/a), fail=None, time(sec)=0, disc reason=0x1F06
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_LINE_CALL_REC: ct_hndl=23,
rx/tx levl=0/255, phase-jit: freq=0.0, levl=0, far-end echo-le
vl=0, freq offst=0.0, phase-roll=0.0, round-trip=0, d-pad=None, d-pad
comp=0, rbs=0, const=None rx/tx: sym-rate=0/0, carr-freq=0/0,
trel-code=0/0, preemph-index=0/0, rx/tx: const-shape=Off/Off,
nonlin-encode=Off/Off, precode=Off/Off, xmit levl-reduct=0/0, shape=0x
0000000000000000000000000000000000000000000000000000
Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_INFO_CALL_REC: ct_hndl=23,
general info=0x0, rx/tx link-layer=0/0, NAKs=0/0, rx/tx ppp-sl
ip=0/0, bad ppp-slip=0, proj max rx b-rate: client=0, host=0, rx/tx:
max neg I frame=0/0, neg window=0/0, T401 timeouts=0, tx window
closures=0, rx overruns=0, retrans frames=0, v110: rx good=0, rx
bad=0, tx=0, sync-lost=0, ss7/cot=0x00, v42bis size: dict=0, strin
g=0, test err=0, reset=0, v0 synch-loss=0, mail lost: host=0, sp=0,
diag=0x00000000000000000000000000000000
Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_NEG_CALL_REC: ct_hndl=23,
v90 train=0x00000000, v90 sgn-ptrn=0x00000000, state trnsn=0x00
00000000000000000000000000000000000000000000000000000000000000,
phase2=0x00000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000
My config is (some lines have been left out to try and reduce the post
length)...
version 12.3
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service compress-config
!
hostname HDWD-GW-DIAL1
!
no boot startup-test
enable secret 5 xxxxxxxxxxxxxxxxxxxxx
!
username administrator password 7 xxxxxxxxx
username manager privilege 6 password 7 xxxxxxxxx
username test password 0 test
!
!
resource-pool disable
clock timezone gmt 0
clock summer-time bst recurring
clock calendar-valid
calltracker enable
calltracker history max-size 200
calltracker call-record verbose
spe call-record modem
!
spe default-firmware spe-firmware-1
aaa new-model
!
!
aaa authentication login netenguk group tacacs+ line
aaa authentication login console group tacacs+ none
aaa authentication ppp default group tacacs+ none
aaa authentication ppp ppptac group tacacs+ none
aaa authorization exec netenguk group tacacs+ none
aaa authorization commands 15 netenguk group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
ip subnet-zero
ip domain name 555.co.uk
ip name-server 5.5.31.7
ip name-server 5.5.95.7
!
ip cef
ip address-pool local
ip dhcp-server 5.5.31.7
ip dhcp-server 5.5.95.7
mpls ldp logging neighbor-changes
isdn switch-type primary-net5
isdn voice-call-failure 0
no scripting tcl init
no scripting tcl encdir
!
!
!
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
!
!
!
!
!
!
!
controller E1 7/0
framing NO-CRC4
pri-group timeslots 1-30
!
controller E1 7/1
!
controller E1 7/2
!
controller E1 7/3
!
controller E1 7/4
!
controller E1 7/5
!
controller E1 7/6
!
controller E1 7/7
bridge irb
!
!
interface Loopback0
ip address 192.168.240.231 255.255.255.255
no ip mroute-cache
!
interface FastEthernet0/0
ip address 5.5.20.2 255.255.255.0
no ip mroute-cache
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
clockrate 2000000
!
interface Serial7/0
no ip address
shutdown
!
interface Serial0/1
no ip address
shutdown
clockrate 2000000
!
interface Serial7/0:15
no ip address
encapsulation ppp
no ip route-cache
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
isdn calling-number 376800
no fair-queue
no cdp enable
!
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
no ip mroute-cache
async mode dedicated
peer default ip address pool pool_dialup
ppp authentication chap pap callin
group-range 1/00 1/107
hold-queue 75 in
!
interface Group-Async1
ip unnumbered FastEthernet0/0
no ip route-cache
no ip mroute-cache
dialer in-band
dialer rotary-group 1
async default routing
async mode dedicated
peer default ip address pool pool_dialup
ppp authentication chap pap callin
group-range 3/00 3/59
!
interface Dialer1
ip unnumbered FastEthernet0/0
encapsulation ppp
no ip mroute-cache
dialer in-band
dialer idle-timeout 2700 either
dialer watch-group 1
dialer-group 1
peer default ip address pool pool_dialup
no fair-queue
no cdp enable
ppp authentication chap pap callin
ppp multilink
!
ip local pool pool_dialup 5.5.20.245 5.5.20.250
ip classless
ip route 0.0.0.0 0.0.0.0 5.5.20.254
no ip http server
no ip http secure-server
!
!
dialer-list 1 protocol ip permit
!
voice-port 7/0:D
!
ss7 mtp2-variant Bellcore 0
ss7 mtp2-variant Bellcore 1
ss7 mtp2-variant Bellcore 2
ss7 mtp2-variant Bellcore 3
!
line 1/00 1/107
exec-timeout 0 0
no flush-at-activation
modem InOut
rotary 1
transport input all
line 3/00 3/59
exec-timeout 0 0
no flush-at-activation
modem InOut
rotary 1
transport input all
!
scheduler allocate 10000 400
end
|
|
0
|
|
|
|
Reply
|
 david.sawyer (2)
|
2/15/2006 4:14:01 PM |
|
Just a quick one, I had alot of trouble last time until I upgraded IOS.
Also why don't you try local authentication first.
I'll post send you one of my working configs if you need okay.
D
FixitDave wrote:
> I'm trying to setup an AS5400 for in/out modem/ISDN access, firstly I'd
> just like to configure for modem access, but when I dial into it I get
> the following output (debug isdn q931, isdn error & spe modem
> errors)...The dialing modem just keeps whistling then responds with 'no
> carrier'
>
> Jan 3 04:56:56.826 gmt: ISDN Se7/0:15 Q931: RX <- SETUP pd = 8
> callref = 0x0001
> Sending Complete
> Bearer Capability i = 0x8090A3
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Called Party Number i = 0x81, '376800'
> Plan:ISDN, Type:Unknown
> Jan 3 04:56:56.826 gmt: PM_ST_MODEM_ERR: pm_modem_mgmt_get_modem_parm:
> no hwidb/tty
> Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> CALL_PROC pd = 8
> callref = 0x8001
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> ALERTING pd = 8
> callref = 0x8001
> Jan 3 04:56:56.834 gmt: ISDN Se7/0:15 Q931: TX -> CONNECT pd = 8
> callref = 0x8001
> Jan 3 04:56:56.934 gmt: ISDN Se7/0:15 Q931: RX <- CONNECT_ACK pd = 8
> callref = 0x0001
>
> ****debug waits here for a while, then 'no carrier' on dialing
> modem****
>
> Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: RX <- DISCONNECT pd = 8
> callref = 0x0001
> Cause i = 0x8090 - Normal call clearing
> Progress Ind i = 0x8288 - In-band info or appropriate now
> available
> Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: TX -> RELEASE pd = 8
> callref = 0x8001
> Jan 3 04:57:52.307 gmt: ISDN Se7/0:15 Q931: RX <- RELEASE_COMP pd = 8
> callref = 0x0001
> Jan 3 04:57:53.327 gmt:
> %MODEMCALLRECORD-6-PM_TERSE_CALL_FAILED_RECORD: DS0
> slot/contr/chan=7/0/1, slot/port=1/13, call_id=E, calli
> ng=(n/a), called=376800, time=0, finl-state=Half Duplex Train,
> disc(modem)=1F06 <unknown>/Requested by host/network indicated discon
> nect
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-TRACE_HDR:
>
> Modem 1/13 Events Log:
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
> Jan 1 00:03:47.843 gmt: Port State Reached:
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
> Jan 1 00:03:47.847 gmt: Port State Reached:
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-CSM_IC_CALLED_NUM:
> Jan 3 04:56:56.830 gmt: ISDN incoming called number: 376800
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
> Jan 3 04:56:56.834 gmt: Port State Reached:
> Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
> Jan 3 04:56:56.942 gmt: Port State Reached:
> Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
> Jan 3 04:56:56.942 gmt: Modem State event:
> State: Connect
> Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
> Jan 3 04:56:59.366 gmt: Modem State event:
> State: V.8bis Exchange
> Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
> Jan 3 04:57:00.638 gmt: Modem State event:
> State: Quick Connect
> Jan 3 04:58:00.291 gmt: %CALLTRKR-6-CALL_RECORD: ct_hndl=23,
> service=None, origin=Answer, category=Modem, DS0 slot/port/ds1/chan=7/
> 0/0/0, called=376800, calling=(n/a), resource slot/port=1/13,
> userid=(n/a), ip=0.0.0.0, mask=0.0.0.0, account id=165, setup=01/03/20
> 00 04:56:54, conn=0.11, phys=0.00, service=0.00, authen=0.00,
> init-rx/tx b-rate=64000/64000, rx/tx chars=0/0, time=55.42, disc subsy
> s=ISDN, disc code=0x10, disc text=Normal call clearing
> Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_CALL_REC: ct_hndl=23, prot:
> last=SYNC Mode, attempt=SYNC Mode, comp: last=None, atmp= Non
> e, std: last=V.21, attempt=V.21, init=V.21, snr=0, sq=0, rx/tx:
> chars=0/0, ec: rx/tx=0/0, rx bad=0, rx/tx b-rate: last=13408/13408,
> low=13408/13408, high=300/300, desired-client=(n/a)/(n/a),
> desired-host=(n/a)/(n/a), retr: local=0, remote=0, fail=0, speedshift:
> lo
> cal up/down=0/0, remote up/down=0/0, fail=0, v90: stat=No Attempt,
> client=(n/a), fail=None, time(sec)=0, disc reason=0x1F06
> Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_LINE_CALL_REC: ct_hndl=23,
> rx/tx levl=0/255, phase-jit: freq=0.0, levl=0, far-end echo-le
> vl=0, freq offst=0.0, phase-roll=0.0, round-trip=0, d-pad=None, d-pad
> comp=0, rbs=0, const=None rx/tx: sym-rate=0/0, carr-freq=0/0,
> trel-code=0/0, preemph-index=0/0, rx/tx: const-shape=Off/Off,
> nonlin-encode=Off/Off, precode=Off/Off, xmit levl-reduct=0/0, shape=0x
> 0000000000000000000000000000000000000000000000000000
> Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_INFO_CALL_REC: ct_hndl=23,
> general info=0x0, rx/tx link-layer=0/0, NAKs=0/0, rx/tx ppp-sl
> ip=0/0, bad ppp-slip=0, proj max rx b-rate: client=0, host=0, rx/tx:
> max neg I frame=0/0, neg window=0/0, T401 timeouts=0, tx window
> closures=0, rx overruns=0, retrans frames=0, v110: rx good=0, rx
> bad=0, tx=0, sync-lost=0, ss7/cot=0x00, v42bis size: dict=0, strin
> g=0, test err=0, reset=0, v0 synch-loss=0, mail lost: host=0, sp=0,
> diag=0x00000000000000000000000000000000
> Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_NEG_CALL_REC: ct_hndl=23,
> v90 train=0x00000000, v90 sgn-ptrn=0x00000000, state trnsn=0x00
> 00000000000000000000000000000000000000000000000000000000000000,
> phase2=0x00000000000000000000000000000000000000000000000000000000000
> 00000000000000000000000000000000000000000000000000000
>
> My config is (some lines have been left out to try and reduce the post
> length)...
> version 12.3
> no service pad
> service timestamps debug datetime msec localtime show-timezone
> service timestamps log datetime msec localtime show-timezone
> service password-encryption
> service compress-config
> !
> hostname HDWD-GW-DIAL1
> !
> no boot startup-test
> enable secret 5 xxxxxxxxxxxxxxxxxxxxx
> !
> username administrator password 7 xxxxxxxxx
> username manager privilege 6 password 7 xxxxxxxxx
> username test password 0 test
> !
> !
> resource-pool disable
> clock timezone gmt 0
> clock summer-time bst recurring
> clock calendar-valid
> calltracker enable
> calltracker history max-size 200
> calltracker call-record verbose
> spe call-record modem
> !
> spe default-firmware spe-firmware-1
> aaa new-model
> !
> !
> aaa authentication login netenguk group tacacs+ line
> aaa authentication login console group tacacs+ none
> aaa authentication ppp default group tacacs+ none
> aaa authentication ppp ppptac group tacacs+ none
> aaa authorization exec netenguk group tacacs+ none
> aaa authorization commands 15 netenguk group tacacs+ none
> aaa accounting exec default start-stop group tacacs+
> aaa accounting commands 15 default start-stop group tacacs+
> aaa session-id common
> ip subnet-zero
> ip domain name 555.co.uk
> ip name-server 5.5.31.7
> ip name-server 5.5.95.7
> !
> ip cef
> ip address-pool local
> ip dhcp-server 5.5.31.7
> ip dhcp-server 5.5.95.7
> mpls ldp logging neighbor-changes
> isdn switch-type primary-net5
> isdn voice-call-failure 0
> no scripting tcl init
> no scripting tcl encdir
> !
> !
> !
> !
> !
> !
> !
> !
> no voice hpi capture buffer
> no voice hpi capture destination
> !
> !
> !
> !
> !
> !
> !
> !
> !
> controller E1 7/0
> framing NO-CRC4
> pri-group timeslots 1-30
> !
> controller E1 7/1
> !
> controller E1 7/2
> !
> controller E1 7/3
> !
> controller E1 7/4
> !
> controller E1 7/5
> !
> controller E1 7/6
> !
> controller E1 7/7
> bridge irb
> !
> !
> interface Loopback0
> ip address 192.168.240.231 255.255.255.255
> no ip mroute-cache
> !
> interface FastEthernet0/0
> ip address 5.5.20.2 255.255.255.0
> no ip mroute-cache
> duplex auto
> speed auto
> !
> interface FastEthernet0/1
> no ip address
> shutdown
> duplex auto
> speed auto
> !
> interface Serial0/0
> no ip address
> shutdown
> clockrate 2000000
> !
> interface Serial7/0
> no ip address
> shutdown
> !
> interface Serial0/1
> no ip address
> shutdown
> clockrate 2000000
> !
> interface Serial7/0:15
> no ip address
> encapsulation ppp
> no ip route-cache
> dialer rotary-group 1
> dialer-group 1
> isdn switch-type primary-net5
> isdn incoming-voice modem
> isdn calling-number 376800
> no fair-queue
> no cdp enable
> !
> interface Group-Async0
> ip unnumbered FastEthernet0/0
> encapsulation ppp
> no ip mroute-cache
> async mode dedicated
> peer default ip address pool pool_dialup
> ppp authentication chap pap callin
> group-range 1/00 1/107
> hold-queue 75 in
> !
> interface Group-Async1
> ip unnumbered FastEthernet0/0
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer rotary-group 1
> async default routing
> async mode dedicated
> peer default ip address pool pool_dialup
> ppp authentication chap pap callin
> group-range 3/00 3/59
> !
> interface Dialer1
> ip unnumbered FastEthernet0/0
> encapsulation ppp
> no ip mroute-cache
> dialer in-band
> dialer idle-timeout 2700 either
> dialer watch-group 1
> dialer-group 1
> peer default ip address pool pool_dialup
> no fair-queue
> no cdp enable
> ppp authentication chap pap callin
> ppp multilink
> !
> ip local pool pool_dialup 5.5.20.245 5.5.20.250
> ip classless
> ip route 0.0.0.0 0.0.0.0 5.5.20.254
> no ip http server
> no ip http secure-server
> !
> !
> dialer-list 1 protocol ip permit
> !
> voice-port 7/0:D
> !
> ss7 mtp2-variant Bellcore 0
> ss7 mtp2-variant Bellcore 1
> ss7 mtp2-variant Bellcore 2
> ss7 mtp2-variant Bellcore 3
> !
> line 1/00 1/107
> exec-timeout 0 0
> no flush-at-activation
> modem InOut
> rotary 1
> transport input all
> line 3/00 3/59
> exec-timeout 0 0
> no flush-at-activation
> modem InOut
> rotary 1
> transport input all
> !
> scheduler allocate 10000 400
> end
|
|
|
0
|
|
|
|
Reply
|
 genki
|
2/15/2006 5:07:39 PM
|
|
Please do send your config, could you also confirm your IOS image that
you're running...thanks
|
|
|
0
|
|
|
|
Reply
|
FixitDave
|
2/17/2006 10:46:59 AM
|
|
Hi...not wanting to push you for this, but do you have your IOS image
details and your config to hand.
Thanks
FixitDave wrote:
> Please do send your config, could you also confirm your IOS image that
> you're running...thanks
|
|
|
0
|
|
|
|
Reply
|
FixitDave
|
2/20/2006 2:33:29 PM
|
|
Oops sorry, here ya go, this one is working in production, Radius Auth
(nortel bay secure) but it's a T3 with
a few T1's on it and NFAS so your line config will prob be different.
Also I'm in the States so back home uk config is
different.
when I was getting this one going I had loadsa problems with CallerID
and hit a bug in the IOS I was running,
upgrading to the version below fixed it.
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
no service password-encryption
!
hostname 5350
!
boot system flash c5350-is-mz.122-15.T8.bin
no boot startup-test
logging queue-limit 100
enable secret 5
username xxxx password 0 xxxx
!
!
resource-pool disable
clock timezone EST -5
spe country usa
!
spe default-firmware spe-firmware-1
aaa new-model
!
!
aaa authentication ppp default group radius
aaa authorization exec default local
aaa authorization network default group radius
aaa accounting network default start-stop group radius
aaa session-id common
ip subnet-zero
ip cef
no ip domain lookup
!
isdn switch-type primary-ni
!
!
!
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
!
fax interface-type fax-mail
mta receive maximum-recipients 0
!
!
!
controller T1 3/0
framing esf
linecode b8zs
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 0
description xxxxx
!
controller T1 3/1
framing esf
linecode b8zs
pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 0
description xxxxxxx
!
controller T1 3/2
framing sf
linecode ami
!
controller T1 3/3
framing sf
linecode ami
!
!
interface FastEthernet0/0
ip address 207.127.253.80 255.255.255.0
duplex full
speed 100
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed 10
!
interface Serial0/0
no ip address
shutdown
clockrate 2000000
!
interface Serial0/1
no ip address
shutdown
clockrate 2000000
!
interface Serial3/0:23
no ip address
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice modem
ppp authentication chap
!
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer in-band
dialer idle-timeout 300
dialer-group 1
async mode interactive
peer default ip address pool dialin
no keepalive
ppp authentication chap
group-range 1/00 1/107
!
router rip
version 2
passive-interface Group-Async0
network 192.168.250.0
network 207.127.253.0
no auto-summary
!
ip local pool dialin 1.1.1.1 1.1.1.253
ip classless
ip route 0.0.0.0 0.0.0.0 207.127.253.34
no ip http server
!
!
!
dialer-list 1 protocol ip permit
!
!
radius-server host 192.168.132.60 auth-port 1645 acct-port 1646
radius-server key xxxxxxxx
radius-server authorization permit missing Service-Type
call rsvp-sync
!
voice-port 3/0:D
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
line 1/00 1/107
timeout login response 0
no flush-at-activation
no modem callout
modem Dialin
transport input all
autoselect during-login
autoselect ppp
!
scheduler allocate 10000 400
end
|
|
|
0
|
|
|
|
Reply
|
genki
|
2/21/2006 5:07:33 PM
|
|
|
4 Replies
30 Views
(page loaded in 0.138 seconds)
|
Search |
Post Question |
Groups |
Stream |
About |
Register
24755 articles. 
23 followers. 