searching for a DSP board
I am searching for a DSP board ( TI TMS320C6x series of processor), which would take 21 channels of analog EEG signals convert it to digital with a sampling rate of 256Hz and process (such as doing FFT) individually and parallelly of individual channel. please suggest me a DSP board or plan to implement thanks
santoz4u
comp.dsp
20333 articles. 
1 followers.
allnor
0 Replies
688 Views
Similar Artilces:
DSP Group TeakLite DSP Board
I've pulled a DSP Group Teak Lite DSP development board out of the bin at work. It's about 3-4 years old. Their web site asks you to login before you can look at docs an support S/W etc. Does anyone have an old support login for this site? Cheers, Alfie. ...
Searching SBC/DSP board/microcontroller; 4ADC/1kHz/USB Host
Hello, I am looking for something along the lines of a Single Board Computer (SBC), a Digital Signal Processing (DSP) board, or a microcontroller. Though I am open to any other suggestions, but what I essentially need to be able to do is the following. Requirements: - 4 channel ADC - Sample rate of 1kHz; meaning I want to be able to sample from all 4 channels at a rate of 1kHz, whether that means sampling each input individually (in a round-like fashion at a higher rate in order to complete sampling all 4 channels at an overall rate of 1kHz), or sampling all 4 channels at the same time each at a rate of 1kHz. - Can write to USB (USB Host port) Project Breakdown: I have 4 analogue signals I need converted to digital signals, and store on a USB key, at a rate of 1kHz. I am very new to working with these pieces of equipment, so please be understanding if I make any errors in talking about them, or am completely mistaken about the components to use. I have so far been steered in the direction of using a SBC or a DSP board. However, I’ve been searching for days going over board after board, and I can’t find anything that has a high enough sample rate. The closest I’ve found to what I need is a series of ARM single board computers, the TS-7000 series. http://www.embeddedarm.com/products/arm-sbc.php#ts-7800-series Other than the TS-7800, the others didn’t seem to come close enough. Even the TS-7800, after reading the manual closely and inquiring about the meanings of so...
Dsp
To do well dsp what areas of math I must know well, and also what dsp starter kit for learning you would recommend me? Dave Dave wrote: > To do well dsp what areas of math I must know well, and also what dsp > starter kit for learning you would recommend me? > > Dave > Try this page: www.dspguru.com And check out the beginner books section. Rick Lyons' book is an excellent place to start. R I recommend following Math area: Probability , statistics, random theory DSP kit: ADSP 2181, SHARC, TMS 320C54xx ArunKumar "Dave" <davecle@SoftHome.net> wr...
Which DSP vendor has the best DSP architecture and why?
There are 4 major supplier of general purpose DSPs; Agere, TI, Analog Devices and Motorola. Which DSP vendor has the best DSP architecture(s), DSPs, tools, support and why? Thanks.........dp On 19 Dec 2003 19:25:35 -0800, petkevich@yahoo.com (dp) wrote: >There are 4 major supplier of general purpose DSPs; Agere, TI, Analog >Devices and Motorola. Which DSP vendor has the best DSP >architecture(s), DSPs, tools, support and why? > >Thanks.........dp Your question tickled me. It's like asking, "Who makes the best gasoline-powered vehicle, who has the best maintenan...
DSP using a non DSP processor
My requirement is to use a moderate controller (Non DSP) and take analog sinusoidal signals (half second cycle 50 hz) , take their samples, do a Fourier transform to remove harmonics and then multiply them to find instantaneous power. Then do a Low Power Filtering operation on this power signal. Is it possible? has anyone implemented anything similar or am I being too ambitious? please post your comments about its feasibility. Thanks, Rohan Rohan wrote: > My requirement is to use a moderate controller (Non DSP) and take > analog sinusoidal signals (half second cycle 50 hz) , take their > samples, do a Fourier transform to remove harmonics and then multiply > them to find instantaneous power. Then do a Low Power Filtering > operation on this power signal. > Is it possible? has anyone implemented anything similar or am I being > too ambitious? > please post your comments about its feasibility. > > Thanks, > Rohan > The big question is "in real time?". Do you want to do this in C ? So, Yea but, is your answer. Rohan wrote: > My requirement is to use a moderate controller (Non DSP) and take > analog sinusoidal signals (half second cycle 50 hz) , take their > samples, do a Fourier transform to remove harmonics and then multiply > them to find instantaneous power. Then do a Low Power Filtering > operation on this power signal. > Is it possible? has anyone implemented anything similar or am I being > too a...
/dev/dsp... how to target different dsp ?
i'm using xmms... and after doing a cvsup/rebuild from (8.0-release) to: FreeBSD elhdt.hoe 8.1-PRERELEASE FreeBSD 8.1-PRERELEASE #3: Sat Jun 12 15:39:04 PDT 2010 root@elhdt:/usr/obj/usr/src/sys/GENERIC i386 xmms nolonger works... and i think that problem is that 8.1-pre- release can now see additional sound devices that weren't seen before... my problem, is how do i get xmms working again (i think, rebind the /dev/dsp device?) how to bind /dev/dsp to a different beast.... elhdt# ls -l /dev/dsp crw-rw-rw- 1 root wheel 0, 117 Jun 18 13:07 /dev/dsp elhdt# ls -l /dev/dsp* crw-rw-rw- 1 root wheel 0, 111 Jun 17 15:41 /dev/dsp0.0 crw-rw-rw- 1 root wheel 0, 117 Jun 18 13:07 /dev/dsp0.1 crw-rw-rw- 1 root wheel 0, 90 Jun 17 15:41 /dev/dsp1.0 crw-rw-rw- 1 root wheel 0, 89 Jun 17 15:41 /dev/dsp2.0 crw-rw-rw- 1 root wheel 0, 88 Jun 17 15:41 /dev/dsp3.0 crw-rw-rw- 1 root wheel 0, 87 Jun 17 15:41 /dev/dsp4.0 hmm... clearly, devfs is synthesizing the response to the stat for /dev/dsp by the first ls -l, and the second shows that /dev/dsp is not really there, (the shell expansion of '*' doesn't see it) - so /dev/dsp is probably some sort of artificial virtual object synthesized by devfs. my problem is this. i want to bind to the dsp3.0 (pcm3) equivalent device, and not the pcm equivalent device (i think). how can i do this ? any help or suggestions would be appreciated! elh...
DSP boards manufacturers
Hi everybody Maybe it isn't proper group (so sorry for that) but I'd like to ask if You can send Me some webites of DSP boards manufacturers. I want to present them a dsp board (excellent for Power Electronics sytems - DSP + FPGA + A/D + D/A etc.) that I prepared. Regards Greg Grzegorz <ggrabo@tlen.pl> wrote in news:dih0pk$11m$1@news.task.gda.pl: > Hi everybody > > Maybe it isn't proper group (so sorry for that) but I'd like to ask if > You can send Me some webites of DSP boards manufacturers. I want to > present them a dsp board (excellent for Power Electronics sytems - DSP > + FPGA + A/D + D/A etc.) that I prepared. > > Regards > Greg > Check out our web site. We have Sharc DSP-FPGA boards, I/O etc. -- Al Clark Danville Signal Processing, Inc. -------------------------------------------------------------------- Purveyors of Fine DSP Hardware and other Cool Stuff Available at http://www.danvillesignal.com >Hi everybody > >Maybe it isn't proper group (so sorry for that) but I'd like to ask if >You can send Me some webites of DSP boards manufacturers. I want to >present them a dsp board (excellent for Power Electronics sytems - DSP >+ FPGA + A/D + D/A etc.) that I prepared. Well, if you can tell us which DSP you used you would atleast narrow dow folks interested in the design, if any. Atleast I would be interested i you used say a TMS320C6455 or even TMS320C6713. See? --Bhoos...
for TMS320LF2407A DSP board
I am a ME student of Bengal Engg. & Sc. University. I am going to develop a DSP controller board using TMS320LF2407A DSP chip.Enybody can help me in this perpose? Thanking you Goutam Adak BESU, HOWRAH-3, INDIA Ph: +919339204687 which application are you orient? "Goutam" <adakgoutam@rediffmail.com> ???? news:ab1c6002.0412040239.18c3a423@posting.google.com... > I am a ME student of Bengal Engg. & Sc. University. I am going to > develop a DSP controller board using TMS320LF2407A DSP chip.Enybody > can help me in this perpose? > Thanking you > > Gouta...
DSP@
DSP@ fetches the address of the top of stack, and places it on the stack. In doing so, of course, a new stack entry has to be created. So, which address goes on the stack? The previous one (before the new stack entry) or the new one? Currently, my code uses the new address: INCT R4 - create new stack entry MOV R4,*R4 - place address of stack pointer in top stack entry Mark. Op Mon, 13 Apr 2009 10:58:16 -0700 (PDT) schreef MarkWills: > DSP@ fetches the address of the top of stack, and places it on the > stack. > > In doing so, of course, a new stack entry has to be created. So, which > address goes on the stack? The previous one (before the new stack > entry) or the new one? > > Currently, my code uses the new address: > > INCT R4 - create new stack entry > MOV R4,*R4 - place address of stack pointer in top stack entry > > Mark. If you have a machine with no native PUSH and POP, you can choose either of them. Strange to see a stack growing upwards, do you use a TI 99 or something? FIGFORTH for the 1802 had the data stack growing upwards and the return stack downwards. If the sequence 'DSP@ DSP!' does not change DEPTH, you're ok. On an Intel/AMD/Cyrix etc. PC you can do 'PUSH SP' followed by 'POP SP' and the stack pointer will not change, providing you do this on a 286 (just checked;-) or higher. -- Coos CHForth, 16 bit DOS applications http://home.hccnet.nl/j.j.haak/forth.html MarkWills <mar...
DSP experiment board
Hello Comp.DSP! I have recently made first contact with the DSP-world in a undergraduate course where I have been using a Texas Instruments C6711 DS Starter Kit. I would like to get suggestions on other DSP-boards with integrate AD/DA:s for audio applications that I might buy and continue experimentin with at home. (It doesn't need to be Texas Instruments) Are there any good alternatives out there? Thanks in advance, Viktor On May 26, 9:16 am, "luminous" <vikt...@mail.nu> wrote: > Hello Comp.DSP! I have recently made first contact with the DSP-world in an > undergraduate course where I have been using a Texas Instruments C6711 DSP > Starter Kit. > > I would like to get suggestions on other DSP-boards with integrated > AD/DA:s for audio applications that I might buy and continue experimenting > with at home. (It doesn't need to be Texas Instruments) > Are there any good alternatives out there? > > Thanks in advance, > Viktor One suggestion is the TMS320C6713 DSP starter kit for abut US $400. TI also sells a TMS320C6416 DSP starter kit for about US $500. The 6713 is the floating point version and the 6416 is the fixed point version. If you get either of these kits I also suggest you get the second edition of the book "Digital Signal Processing and Applications with the TMS320C6713 and MS320C6416. DSK" by Ralph Chassaing and Donald Reay. The book has a large set of demostration programs for these kits a...
Help on DSP boards.
Hi, I am a CS student and an absolute newbie to the world of DSPs. I need to evaluate DSP boards that I can use to do some computation intensive operations in C programming. For example Kloosterman's sum K(a,b;p)=\sum e_p(ax+bx^*) , where ep(t) = e2pit / p and x* is the inverse of x modulo p and p is a prime number. I was wondering which DSP board I can use. I would want something that: 1. Be connected through USB/JTAG. 2. Can be programmed in C and has a good cross compiler, debugger and environment so that my environment is easy to use. Ideally, I would be doing this on 2-3 boards and come up with a performance analysis. Any help is appreciated. Thanks, Krushna I suggest you investigate using a PC with fast Pentium processor first especially when used in conjunction with Intel's Performance Primative library. At work, we have ceased using dedicated DSP boards, and now build ou systems based solely on Pentium CPUs. Our applications include HF Passiv Sonar, which is very demanding of processing power to run in real-time You can save megabucks taking this approach. Jeff Hi Jeff, This is more of an experiment than practical application. What we want for our performance analysis are results of the computation on say a fast Pentium processor and two-three DSP boards so that we know how useful it is to do such a thing. Since we are going to buy just a single DSP toolkit or two, cost should not be a consideration. The funding for that too is expect...
which DSP?
Hello, I have a Yakumo Hypersound 128 MP3-Player and would like to modify the firmware. Can anybody tell we, which DSP is used? Thank you in advance, Daniel ...
DSP evaluation board
Hello, Sorry for my english, i'm french... I am newbie with the programming of DSP. I am in the search of an DSP evaluation board which also proposes a ADC and be programmable with a C environnement. The main use of this DSP board will be training and FFT calculation by sampling 10.7 Mhz IF frequency of an HF receiver. At this moment I didn't find an evaluation board with enough powerful ADC. My choice is made on a 2812EVM-I sold at GAO TEK. but it's does not seem the best choice. If somebody know a good evaluation Board with a minimum of 20 Msps AdC or a daughter board not too expensive In advance thanks Best regard Regardez chez Analog Devices du c�t� des Blackfin Amities JP F5MI http://perso.orange.fr/F5mi.64 "shaders" <shaders.2devs@gmail.com> a �crit dans le message de news: 1188498824.864956.326870@x40g2000prg.googlegroups.com... > Hello, > > Sorry for my english, i'm french... > > I am newbie with the programming of DSP. I am in the search of an DSP > evaluation board which also proposes a ADC and be programmable with a > C environnement. > > The main use of this DSP board will be training and FFT calculation by > sampling 10.7 Mhz IF frequency of an HF receiver. > > At this moment I didn't find an evaluation board with enough powerful > ADC. > > My choice is made on a 2812EVM-I sold at GAO TEK. but it's does not > seem the best choice. > > If somebody kno...
ADC Board with DSP
Hello, I am looking for a ADC Board with DSP . I have been searching throug google but unfortunately I have no success. Does anyone know commercial boards with the following characteristics? Computer bus: PCI At least 2 A/D channel Resolution: 8 bits or higher Sample frequency: 10MHz or higher With DSP (for my own algorithms) Drivers for Linux Thanks in advance, Marcos Vin�cius The Conejo Board from Innovative Integration offers all but the Linux drivers. It has a TI DSP on card and 4 A/D with 14 bit resolution at 10 MHz. -V MarcosOmni wrote: > Hello, > > I am looking for a ADC Board with DSP . I have been searching through > google but unfortunately I have no success. > > Does anyone know commercial boards with the following characteristics? > > Computer bus: PCI > At least 2 A/D channel > Resolution: 8 bits or higher > Sample frequency: 10MHz or higher > With DSP (for my own algorithms) > Drivers for Linux See the thread "Recommendation for PCI DSP board?" last activity 7/18. Linux drivers might be the sticking point. Jerry -- Engineering is the art of making what you want from things you can get. ����������������������������������������������������������������������� ...
Modem DSP board
Hi Everyone, I have a DSP daughter board that is from an older, 14k US Robotics modem. The board has two Texas 320C25 processors and an Intel 188 variant. The board is Model 0147. Any chance finding some documentation on that board? I would not mind playing with it! Thanks, Peter ...
Looking for DSP board
Hi, I'm looking for a DSP board with following requirements: - Texas Instruments processor - Resource board for media, not only signal board - At least four E1/T1 ports - Possibility to load own software Surf would be good, but there is only two E1/T1, Signalogic has not E1/T1 at all and Aculab has not TI processor. Very hard to find correct or impossible??? nieminen.mikko@gmail.com wrote: > Hi, > > I'm looking for a DSP board with following requirements: > - Texas Instruments processor > - Resource board for media, not only signal board > - At least four E1/T1 ports > - Possibility to load own software > > Surf would be good, but there is only two E1/T1, Signalogic has not > E1/T1 at all and Aculab has not TI processor. Very hard to find > correct or impossible??? TI makes many processors. Asking for a TI processor is like asking for a General Motors vehicle. Jerry -- "The rights of the best of men are secured only as the rights of the vilest and most abhorrent are protected." - Chief Justice Charles Evans Hughes, 1927 ��������������������������������������������������������������������� Jerry Avins kirjoitti: > TI makes many processors. Asking for a TI processor is like asking for a > General Motors vehicle. > C64x would be best. ...
TI DSP Board
hi all, I am a postgraduate researcher based in Ireland. I am currently trying to use Matlab code developed by another researcher on a TMS320C6416 EVM. I have been trying to use the Matlab C compiler to convert the Matlab code to C and then use it in Code Composer Studio to program the chip. However this isn't working correctly. The code will compile fine in CCS but I am unable to build it. The conversion using the matlab compiler like any automatic conversion makes the C code very diificult to understand and I am beginning to think that it would be better to just manually convert the c...
about DSP
Can anyone tell me about the application of DSP in telecommunication? Do you have any technology involved? Thanks <laura_pretty05@yahoo.com.hk> wrote in message news:1142355397.631224.60760@i40g2000cwc.googlegroups.com... > Can anyone tell me about the application of DSP in telecommunication? Yes - it's used all over the place in telecom. Any time you have discrete signals (digitized signals) and they undergo any sort of processing - that's DSP...and there's plenty of that in telecommunication. > Do you have any technology involved? Thanks What do you mean? Clearly there is technology involved - it doesn't happen by magic. Cheers Bhaskar Bhaskar, I mean how telecommunication is used in DSP? Any theory involved? Thanks!! Laura Bhaskar Thiagarajan =E5=AF=AB=E9=81=93=EF=BC=9A > <laura_pretty05@yahoo.com.hk> wrote in message > news:1142355397.631224.60760@i40g2000cwc.googlegroups.com... > > Can anyone tell me about the application of DSP in telecommunication? > > Yes - it's used all over the place in telecom. Any time you have discrete > signals (digitized signals) and they undergo any sort of processing - tha= t's > DSP...and there's plenty of that in telecommunication. > > > Do you have any technology involved? Thanks > > What do you mean? Clearly there is technology involved - it doesn't happen > by magic. >=20 > Cheers > Bhaskar laura_pretty05@yahoo.com.hk ...
dsp.SignalSource not found (dsp System Toolbox is available)
Hi, I'm trying to run the code available here: http://www.mathworks.com/help/dsp/ref/dsp.cicdecimatorclass.html I keep on getting the error : Undefined variable "dsp" or class "dsp.SignalSource". I have dsp System Toolbox Version 8.2 , and I can use other objects inside the DSP package but not SignalSource. Any idea why? Thanks in advance "H Hachem" <hhachem00@gmail.com> wrote in message <kg0mvb$p2b$1@newscl01ah.mathworks.com>... > Hi, > > I'm trying to run the code available here: http://www.mathworks.com/help/dsp/ref/dsp.cicdecimatorclass.html > I keep on getting the error : > Undefined variable "dsp" or class "dsp.SignalSource". > I have dsp System Toolbox Version 8.2 , and I can use other objects inside the DSP package but not SignalSource. Any idea why? > > Thanks in advance I just checked the supported versions. Signalsource is only supported in R2012b, I have R2012a :/ ...
Fixed Point DSP Vs Floating Point DSP
Hi, I searched the internet to find out the difference between a fixed point & a floating point DSP. To my surprise, I did not find a well defined difference. Plz, can anyone differentiate between the two so that a layman can also understand ? Thanx in advance... Sandeep Chikkerur wrote: > > Hi, > > I searched the internet to find out the difference between a fixed > point & a floating point DSP. > To my surprise, I did not find a well defined difference. > > Plz, can anyone differentiate between the two so that a layman can > also understand ? > > Thanx in advance... A fixed-point DSP does only fixed-point arithmetic, and usually has hardware to facilitate multiplication. A floating-point DSP has extra hardware for floating-point addition and multiplication (addition is a bit more involved than multiplication) and often omits the hardware to facilitate fixed-poing multiplication. Expect some difference in the size of a few registers. A matter of curiosity (mine): What difference had you imagined? Jerry -- Engineering is the art of making what you want from things you can get. ����������������������������������������������������������������������� In article <d5d88eb5.0306260219.36f87462@posting.google.com>, sandeep_mc81@yahoo.com says... > Hi, > > I searched the internet to find out the difference between a fixed > point & a floating point DSP. > To my surprise, I did not find a wel...
testing a blackfin DSP board
Hi guys, I'm testing a blackfin DSP board and wanted to get the opinion of you guys on what the best way to ensure that everything works on the board. I've desigined a blackfin dsp board and having it sent to fabricate. I plan to assemble it myself. How would you go about testing that the board is fully functional? Thanks, I appreciate it! JC djcham wrote: > Hi guys, > > I'm testing a blackfin DSP board and wanted to get the opinion of you > guys on what the best way to ensure that everything works on the board. > I've desigined a blackfin dsp board and having it sent to fabricate. I > plan to assemble it myself. How would you go about testing that the > board is fully functional? Thanks, I appreciate it! You give no idea of what populates the board but the processor itself. What do you want to know? What facilities for testing are built in? Jerry -- Engineering is the art of making what you want from things you can get. ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯ > >You give no idea of what populates the board but the processor itself. >...
Got DSP? Senior DSP Communications Engineer-Relo available
Senior Digital Communications Engineer My client, located here in the Silicon Valley, is looking for a talented individual to join the Signal Processing Systems Engineering Team to work concurrently on various state-of-the-art communications systems, both internally and externally. Job Responsibilities This person will possess a range of skills that encompass both broad and deep expertise in the digital communications application space at the systems level in addition to having the skills required to implement the various functions in these systems. The successful candidate will ...
Build my own DSP dev board?
Hi, I'm a recent engineering grad who did 3 courses in DSP but never used an actualy dsp board (all our labs were in Matlab). Does anyone have schematics for a TI or analog devices DSP development board. Or do you know of companies that sell discontinued boards? Thanks "evil engineer" <evil@engr.com> wrote in news:yeqvb.3920$IZ1.3760@edtnps84: > Hi, > > I'm a recent engineering grad who did 3 courses in DSP but never used > an actualy dsp board (all our labs were in Matlab). Does anyone have > schematics for a TI or analog devices DSP development ...
FPGA/DSP/Video Board
Hi, Many thanks for your time. I'm looking for a board to pre-process the video signal from camera. The followings are the features of the camera I will use: -- The camera is of RGB type and has three separate CCD sensors. -- The interface of 3CCD camera is not limited, can be Camera link, GigE, 1394 or analog RGB (three channels), it depends on which kind of development board I can use. -- The frame rate of this camera is about 30f/s, and resolution about 1024*768, 8/10bit. The followings are the features of the board I am looking for: -- Proper interface to receive data from 3CCD ca...
I've pulled a DSP Group Teak Lite DSP development board out of the bin at work. It's about 3-4 years old. Their web site asks you to login before you can look at docs an support S/W etc. Does anyone have an old support login for this site? Cheers, Alfie. ...
Searching SBC/DSP board/microcontroller; 4ADC/1kHz/USB Host
Hello, I am looking for something along the lines of a Single Board Computer (SBC), a Digital Signal Processing (DSP) board, or a microcontroller. Though I am open to any other suggestions, but what I essentially need to be able to do is the following. Requirements: - 4 channel ADC - Sample rate of 1kHz; meaning I want to be able to sample from all 4 channels at a rate of 1kHz, whether that means sampling each input individually (in a round-like fashion at a higher rate in order to complete sampling all 4 channels at an overall rate of 1kHz), or sampling all 4 channels at the same time each at a rate of 1kHz. - Can write to USB (USB Host port) Project Breakdown: I have 4 analogue signals I need converted to digital signals, and store on a USB key, at a rate of 1kHz. I am very new to working with these pieces of equipment, so please be understanding if I make any errors in talking about them, or am completely mistaken about the components to use. I have so far been steered in the direction of using a SBC or a DSP board. However, I’ve been searching for days going over board after board, and I can’t find anything that has a high enough sample rate. The closest I’ve found to what I need is a series of ARM single board computers, the TS-7000 series. http://www.embeddedarm.com/products/arm-sbc.php#ts-7800-series Other than the TS-7800, the others didn’t seem to come close enough. Even the TS-7800, after reading the manual closely and inquiring about the meanings of so...
Dsp
To do well dsp what areas of math I must know well, and also what dsp starter kit for learning you would recommend me? Dave Dave wrote: > To do well dsp what areas of math I must know well, and also what dsp > starter kit for learning you would recommend me? > > Dave > Try this page: www.dspguru.com And check out the beginner books section. Rick Lyons' book is an excellent place to start. R I recommend following Math area: Probability , statistics, random theory DSP kit: ADSP 2181, SHARC, TMS 320C54xx ArunKumar "Dave" <davecle@SoftHome.net> wr...
Which DSP vendor has the best DSP architecture and why?
There are 4 major supplier of general purpose DSPs; Agere, TI, Analog Devices and Motorola. Which DSP vendor has the best DSP architecture(s), DSPs, tools, support and why? Thanks.........dp On 19 Dec 2003 19:25:35 -0800, petkevich@yahoo.com (dp) wrote: >There are 4 major supplier of general purpose DSPs; Agere, TI, Analog >Devices and Motorola. Which DSP vendor has the best DSP >architecture(s), DSPs, tools, support and why? > >Thanks.........dp Your question tickled me. It's like asking, "Who makes the best gasoline-powered vehicle, who has the best maintenan...
DSP using a non DSP processor
My requirement is to use a moderate controller (Non DSP) and take analog sinusoidal signals (half second cycle 50 hz) , take their samples, do a Fourier transform to remove harmonics and then multiply them to find instantaneous power. Then do a Low Power Filtering operation on this power signal. Is it possible? has anyone implemented anything similar or am I being too ambitious? please post your comments about its feasibility. Thanks, Rohan Rohan wrote: > My requirement is to use a moderate controller (Non DSP) and take > analog sinusoidal signals (half second cycle 50 hz) , take their > samples, do a Fourier transform to remove harmonics and then multiply > them to find instantaneous power. Then do a Low Power Filtering > operation on this power signal. > Is it possible? has anyone implemented anything similar or am I being > too ambitious? > please post your comments about its feasibility. > > Thanks, > Rohan > The big question is "in real time?". Do you want to do this in C ? So, Yea but, is your answer. Rohan wrote: > My requirement is to use a moderate controller (Non DSP) and take > analog sinusoidal signals (half second cycle 50 hz) , take their > samples, do a Fourier transform to remove harmonics and then multiply > them to find instantaneous power. Then do a Low Power Filtering > operation on this power signal. > Is it possible? has anyone implemented anything similar or am I being > too a...
/dev/dsp... how to target different dsp ?
i'm using xmms... and after doing a cvsup/rebuild from (8.0-release) to: FreeBSD elhdt.hoe 8.1-PRERELEASE FreeBSD 8.1-PRERELEASE #3: Sat Jun 12 15:39:04 PDT 2010 root@elhdt:/usr/obj/usr/src/sys/GENERIC i386 xmms nolonger works... and i think that problem is that 8.1-pre- release can now see additional sound devices that weren't seen before... my problem, is how do i get xmms working again (i think, rebind the /dev/dsp device?) how to bind /dev/dsp to a different beast.... elhdt# ls -l /dev/dsp crw-rw-rw- 1 root wheel 0, 117 Jun 18 13:07 /dev/dsp elhdt# ls -l /dev/dsp* crw-rw-rw- 1 root wheel 0, 111 Jun 17 15:41 /dev/dsp0.0 crw-rw-rw- 1 root wheel 0, 117 Jun 18 13:07 /dev/dsp0.1 crw-rw-rw- 1 root wheel 0, 90 Jun 17 15:41 /dev/dsp1.0 crw-rw-rw- 1 root wheel 0, 89 Jun 17 15:41 /dev/dsp2.0 crw-rw-rw- 1 root wheel 0, 88 Jun 17 15:41 /dev/dsp3.0 crw-rw-rw- 1 root wheel 0, 87 Jun 17 15:41 /dev/dsp4.0 hmm... clearly, devfs is synthesizing the response to the stat for /dev/dsp by the first ls -l, and the second shows that /dev/dsp is not really there, (the shell expansion of '*' doesn't see it) - so /dev/dsp is probably some sort of artificial virtual object synthesized by devfs. my problem is this. i want to bind to the dsp3.0 (pcm3) equivalent device, and not the pcm equivalent device (i think). how can i do this ? any help or suggestions would be appreciated! elh...
DSP boards manufacturers
Hi everybody Maybe it isn't proper group (so sorry for that) but I'd like to ask if You can send Me some webites of DSP boards manufacturers. I want to present them a dsp board (excellent for Power Electronics sytems - DSP + FPGA + A/D + D/A etc.) that I prepared. Regards Greg Grzegorz <ggrabo@tlen.pl> wrote in news:dih0pk$11m$1@news.task.gda.pl: > Hi everybody > > Maybe it isn't proper group (so sorry for that) but I'd like to ask if > You can send Me some webites of DSP boards manufacturers. I want to > present them a dsp board (excellent for Power Electronics sytems - DSP > + FPGA + A/D + D/A etc.) that I prepared. > > Regards > Greg > Check out our web site. We have Sharc DSP-FPGA boards, I/O etc. -- Al Clark Danville Signal Processing, Inc. -------------------------------------------------------------------- Purveyors of Fine DSP Hardware and other Cool Stuff Available at http://www.danvillesignal.com >Hi everybody > >Maybe it isn't proper group (so sorry for that) but I'd like to ask if >You can send Me some webites of DSP boards manufacturers. I want to >present them a dsp board (excellent for Power Electronics sytems - DSP >+ FPGA + A/D + D/A etc.) that I prepared. Well, if you can tell us which DSP you used you would atleast narrow dow folks interested in the design, if any. Atleast I would be interested i you used say a TMS320C6455 or even TMS320C6713. See? --Bhoos...
for TMS320LF2407A DSP board
I am a ME student of Bengal Engg. & Sc. University. I am going to develop a DSP controller board using TMS320LF2407A DSP chip.Enybody can help me in this perpose? Thanking you Goutam Adak BESU, HOWRAH-3, INDIA Ph: +919339204687 which application are you orient? "Goutam" <adakgoutam@rediffmail.com> ???? news:ab1c6002.0412040239.18c3a423@posting.google.com... > I am a ME student of Bengal Engg. & Sc. University. I am going to > develop a DSP controller board using TMS320LF2407A DSP chip.Enybody > can help me in this perpose? > Thanking you > > Gouta...
DSP@
DSP@ fetches the address of the top of stack, and places it on the stack. In doing so, of course, a new stack entry has to be created. So, which address goes on the stack? The previous one (before the new stack entry) or the new one? Currently, my code uses the new address: INCT R4 - create new stack entry MOV R4,*R4 - place address of stack pointer in top stack entry Mark. Op Mon, 13 Apr 2009 10:58:16 -0700 (PDT) schreef MarkWills: > DSP@ fetches the address of the top of stack, and places it on the > stack. > > In doing so, of course, a new stack entry has to be created. So, which > address goes on the stack? The previous one (before the new stack > entry) or the new one? > > Currently, my code uses the new address: > > INCT R4 - create new stack entry > MOV R4,*R4 - place address of stack pointer in top stack entry > > Mark. If you have a machine with no native PUSH and POP, you can choose either of them. Strange to see a stack growing upwards, do you use a TI 99 or something? FIGFORTH for the 1802 had the data stack growing upwards and the return stack downwards. If the sequence 'DSP@ DSP!' does not change DEPTH, you're ok. On an Intel/AMD/Cyrix etc. PC you can do 'PUSH SP' followed by 'POP SP' and the stack pointer will not change, providing you do this on a 286 (just checked;-) or higher. -- Coos CHForth, 16 bit DOS applications http://home.hccnet.nl/j.j.haak/forth.html MarkWills <mar...
DSP experiment board
Hello Comp.DSP! I have recently made first contact with the DSP-world in a undergraduate course where I have been using a Texas Instruments C6711 DS Starter Kit. I would like to get suggestions on other DSP-boards with integrate AD/DA:s for audio applications that I might buy and continue experimentin with at home. (It doesn't need to be Texas Instruments) Are there any good alternatives out there? Thanks in advance, Viktor On May 26, 9:16 am, "luminous" <vikt...@mail.nu> wrote: > Hello Comp.DSP! I have recently made first contact with the DSP-world in an > undergraduate course where I have been using a Texas Instruments C6711 DSP > Starter Kit. > > I would like to get suggestions on other DSP-boards with integrated > AD/DA:s for audio applications that I might buy and continue experimenting > with at home. (It doesn't need to be Texas Instruments) > Are there any good alternatives out there? > > Thanks in advance, > Viktor One suggestion is the TMS320C6713 DSP starter kit for abut US $400. TI also sells a TMS320C6416 DSP starter kit for about US $500. The 6713 is the floating point version and the 6416 is the fixed point version. If you get either of these kits I also suggest you get the second edition of the book "Digital Signal Processing and Applications with the TMS320C6713 and MS320C6416. DSK" by Ralph Chassaing and Donald Reay. The book has a large set of demostration programs for these kits a...
Help on DSP boards.
Hi, I am a CS student and an absolute newbie to the world of DSPs. I need to evaluate DSP boards that I can use to do some computation intensive operations in C programming. For example Kloosterman's sum K(a,b;p)=\sum e_p(ax+bx^*) , where ep(t) = e2pit / p and x* is the inverse of x modulo p and p is a prime number. I was wondering which DSP board I can use. I would want something that: 1. Be connected through USB/JTAG. 2. Can be programmed in C and has a good cross compiler, debugger and environment so that my environment is easy to use. Ideally, I would be doing this on 2-3 boards and come up with a performance analysis. Any help is appreciated. Thanks, Krushna I suggest you investigate using a PC with fast Pentium processor first especially when used in conjunction with Intel's Performance Primative library. At work, we have ceased using dedicated DSP boards, and now build ou systems based solely on Pentium CPUs. Our applications include HF Passiv Sonar, which is very demanding of processing power to run in real-time You can save megabucks taking this approach. Jeff Hi Jeff, This is more of an experiment than practical application. What we want for our performance analysis are results of the computation on say a fast Pentium processor and two-three DSP boards so that we know how useful it is to do such a thing. Since we are going to buy just a single DSP toolkit or two, cost should not be a consideration. The funding for that too is expect...
which DSP?
Hello, I have a Yakumo Hypersound 128 MP3-Player and would like to modify the firmware. Can anybody tell we, which DSP is used? Thank you in advance, Daniel ...
DSP evaluation board
Hello, Sorry for my english, i'm french... I am newbie with the programming of DSP. I am in the search of an DSP evaluation board which also proposes a ADC and be programmable with a C environnement. The main use of this DSP board will be training and FFT calculation by sampling 10.7 Mhz IF frequency of an HF receiver. At this moment I didn't find an evaluation board with enough powerful ADC. My choice is made on a 2812EVM-I sold at GAO TEK. but it's does not seem the best choice. If somebody know a good evaluation Board with a minimum of 20 Msps AdC or a daughter board not too expensive In advance thanks Best regard Regardez chez Analog Devices du c�t� des Blackfin Amities JP F5MI http://perso.orange.fr/F5mi.64 "shaders" <shaders.2devs@gmail.com> a �crit dans le message de news: 1188498824.864956.326870@x40g2000prg.googlegroups.com... > Hello, > > Sorry for my english, i'm french... > > I am newbie with the programming of DSP. I am in the search of an DSP > evaluation board which also proposes a ADC and be programmable with a > C environnement. > > The main use of this DSP board will be training and FFT calculation by > sampling 10.7 Mhz IF frequency of an HF receiver. > > At this moment I didn't find an evaluation board with enough powerful > ADC. > > My choice is made on a 2812EVM-I sold at GAO TEK. but it's does not > seem the best choice. > > If somebody kno...
ADC Board with DSP
Hello, I am looking for a ADC Board with DSP . I have been searching throug google but unfortunately I have no success. Does anyone know commercial boards with the following characteristics? Computer bus: PCI At least 2 A/D channel Resolution: 8 bits or higher Sample frequency: 10MHz or higher With DSP (for my own algorithms) Drivers for Linux Thanks in advance, Marcos Vin�cius The Conejo Board from Innovative Integration offers all but the Linux drivers. It has a TI DSP on card and 4 A/D with 14 bit resolution at 10 MHz. -V MarcosOmni wrote: > Hello, > > I am looking for a ADC Board with DSP . I have been searching through > google but unfortunately I have no success. > > Does anyone know commercial boards with the following characteristics? > > Computer bus: PCI > At least 2 A/D channel > Resolution: 8 bits or higher > Sample frequency: 10MHz or higher > With DSP (for my own algorithms) > Drivers for Linux See the thread "Recommendation for PCI DSP board?" last activity 7/18. Linux drivers might be the sticking point. Jerry -- Engineering is the art of making what you want from things you can get. ����������������������������������������������������������������������� ...
Modem DSP board
Hi Everyone, I have a DSP daughter board that is from an older, 14k US Robotics modem. The board has two Texas 320C25 processors and an Intel 188 variant. The board is Model 0147. Any chance finding some documentation on that board? I would not mind playing with it! Thanks, Peter ...
Looking for DSP board
Hi, I'm looking for a DSP board with following requirements: - Texas Instruments processor - Resource board for media, not only signal board - At least four E1/T1 ports - Possibility to load own software Surf would be good, but there is only two E1/T1, Signalogic has not E1/T1 at all and Aculab has not TI processor. Very hard to find correct or impossible??? nieminen.mikko@gmail.com wrote: > Hi, > > I'm looking for a DSP board with following requirements: > - Texas Instruments processor > - Resource board for media, not only signal board > - At least four E1/T1 ports > - Possibility to load own software > > Surf would be good, but there is only two E1/T1, Signalogic has not > E1/T1 at all and Aculab has not TI processor. Very hard to find > correct or impossible??? TI makes many processors. Asking for a TI processor is like asking for a General Motors vehicle. Jerry -- "The rights of the best of men are secured only as the rights of the vilest and most abhorrent are protected." - Chief Justice Charles Evans Hughes, 1927 ��������������������������������������������������������������������� Jerry Avins kirjoitti: > TI makes many processors. Asking for a TI processor is like asking for a > General Motors vehicle. > C64x would be best. ...
TI DSP Board
hi all, I am a postgraduate researcher based in Ireland. I am currently trying to use Matlab code developed by another researcher on a TMS320C6416 EVM. I have been trying to use the Matlab C compiler to convert the Matlab code to C and then use it in Code Composer Studio to program the chip. However this isn't working correctly. The code will compile fine in CCS but I am unable to build it. The conversion using the matlab compiler like any automatic conversion makes the C code very diificult to understand and I am beginning to think that it would be better to just manually convert the c...
about DSP
Can anyone tell me about the application of DSP in telecommunication? Do you have any technology involved? Thanks <laura_pretty05@yahoo.com.hk> wrote in message news:1142355397.631224.60760@i40g2000cwc.googlegroups.com... > Can anyone tell me about the application of DSP in telecommunication? Yes - it's used all over the place in telecom. Any time you have discrete signals (digitized signals) and they undergo any sort of processing - that's DSP...and there's plenty of that in telecommunication. > Do you have any technology involved? Thanks What do you mean? Clearly there is technology involved - it doesn't happen by magic. Cheers Bhaskar Bhaskar, I mean how telecommunication is used in DSP? Any theory involved? Thanks!! Laura Bhaskar Thiagarajan =E5=AF=AB=E9=81=93=EF=BC=9A > <laura_pretty05@yahoo.com.hk> wrote in message > news:1142355397.631224.60760@i40g2000cwc.googlegroups.com... > > Can anyone tell me about the application of DSP in telecommunication? > > Yes - it's used all over the place in telecom. Any time you have discrete > signals (digitized signals) and they undergo any sort of processing - tha= t's > DSP...and there's plenty of that in telecommunication. > > > Do you have any technology involved? Thanks > > What do you mean? Clearly there is technology involved - it doesn't happen > by magic. >=20 > Cheers > Bhaskar laura_pretty05@yahoo.com.hk ...
dsp.SignalSource not found (dsp System Toolbox is available)
Hi, I'm trying to run the code available here: http://www.mathworks.com/help/dsp/ref/dsp.cicdecimatorclass.html I keep on getting the error : Undefined variable "dsp" or class "dsp.SignalSource". I have dsp System Toolbox Version 8.2 , and I can use other objects inside the DSP package but not SignalSource. Any idea why? Thanks in advance "H Hachem" <hhachem00@gmail.com> wrote in message <kg0mvb$p2b$1@newscl01ah.mathworks.com>... > Hi, > > I'm trying to run the code available here: http://www.mathworks.com/help/dsp/ref/dsp.cicdecimatorclass.html > I keep on getting the error : > Undefined variable "dsp" or class "dsp.SignalSource". > I have dsp System Toolbox Version 8.2 , and I can use other objects inside the DSP package but not SignalSource. Any idea why? > > Thanks in advance I just checked the supported versions. Signalsource is only supported in R2012b, I have R2012a :/ ...
Fixed Point DSP Vs Floating Point DSP
Hi, I searched the internet to find out the difference between a fixed point & a floating point DSP. To my surprise, I did not find a well defined difference. Plz, can anyone differentiate between the two so that a layman can also understand ? Thanx in advance... Sandeep Chikkerur wrote: > > Hi, > > I searched the internet to find out the difference between a fixed > point & a floating point DSP. > To my surprise, I did not find a well defined difference. > > Plz, can anyone differentiate between the two so that a layman can > also understand ? > > Thanx in advance... A fixed-point DSP does only fixed-point arithmetic, and usually has hardware to facilitate multiplication. A floating-point DSP has extra hardware for floating-point addition and multiplication (addition is a bit more involved than multiplication) and often omits the hardware to facilitate fixed-poing multiplication. Expect some difference in the size of a few registers. A matter of curiosity (mine): What difference had you imagined? Jerry -- Engineering is the art of making what you want from things you can get. ����������������������������������������������������������������������� In article <d5d88eb5.0306260219.36f87462@posting.google.com>, sandeep_mc81@yahoo.com says... > Hi, > > I searched the internet to find out the difference between a fixed > point & a floating point DSP. > To my surprise, I did not find a wel...
testing a blackfin DSP board
Hi guys, I'm testing a blackfin DSP board and wanted to get the opinion of you guys on what the best way to ensure that everything works on the board. I've desigined a blackfin dsp board and having it sent to fabricate. I plan to assemble it myself. How would you go about testing that the board is fully functional? Thanks, I appreciate it! JC djcham wrote: > Hi guys, > > I'm testing a blackfin DSP board and wanted to get the opinion of you > guys on what the best way to ensure that everything works on the board. > I've desigined a blackfin dsp board and having it sent to fabricate. I > plan to assemble it myself. How would you go about testing that the > board is fully functional? Thanks, I appreciate it! You give no idea of what populates the board but the processor itself. What do you want to know? What facilities for testing are built in? Jerry -- Engineering is the art of making what you want from things you can get. ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯ > >You give no idea of what populates the board but the processor itself. >...
Got DSP? Senior DSP Communications Engineer-Relo available
Senior Digital Communications Engineer My client, located here in the Silicon Valley, is looking for a talented individual to join the Signal Processing Systems Engineering Team to work concurrently on various state-of-the-art communications systems, both internally and externally. Job Responsibilities This person will possess a range of skills that encompass both broad and deep expertise in the digital communications application space at the systems level in addition to having the skills required to implement the various functions in these systems. The successful candidate will ...
Build my own DSP dev board?
Hi, I'm a recent engineering grad who did 3 courses in DSP but never used an actualy dsp board (all our labs were in Matlab). Does anyone have schematics for a TI or analog devices DSP development board. Or do you know of companies that sell discontinued boards? Thanks "evil engineer" <evil@engr.com> wrote in news:yeqvb.3920$IZ1.3760@edtnps84: > Hi, > > I'm a recent engineering grad who did 3 courses in DSP but never used > an actualy dsp board (all our labs were in Matlab). Does anyone have > schematics for a TI or analog devices DSP development ...
FPGA/DSP/Video Board
Hi, Many thanks for your time. I'm looking for a board to pre-process the video signal from camera. The followings are the features of the camera I will use: -- The camera is of RGB type and has three separate CCD sensors. -- The interface of 3CCD camera is not limited, can be Camera link, GigE, 1394 or analog RGB (three channels), it depends on which kind of development board I can use. -- The frame rate of this camera is about 30f/s, and resolution about 1024*768, 8/10bit. The followings are the features of the board I am looking for: -- Proper interface to receive data from 3CCD ca...
Web resources about - searching for a DSP board - comp.dsp
Help:Searching - Wikipedia, the free encyclopediaWikipedia has a search engine built in, which can be used to locate material on Wikipedia. The search box is located at the top right on every ...
Spotify Searching, Sharing, Stats Added To Musical Artists’ Facebook PagesMusical artists tied in with Spotify are seeing some new features on their Facebook pages, including the ability by Facebook users to search ...
Facebook Searching For Ways to Break Into Mobile AppsToday’s mobile panel at the Facebook f8 developer conference was notable for the subject it didn’t cover: Facebook itself. With four panelists ...
App Store - RyeBooks: Little Tadpoles Searching for Mommy -by Rye Studio™Get RyeBooks: Little Tadpoles Searching for Mommy -by Rye Studio™ on the App Store. See screenshots and ratings, and read customer reviews.
Searching for the color of moss VII - Flickr - Photo Sharing!Explore tillwe's photos on Flickr. tillwe has uploaded 11549 photos to Flickr.
Skinfan Does Minecraft - Episode 10: Searching for 1.3 - YouTubeHello everyone! Welcome to Skinfan Does Minecraft. In this let's play series I build some things, show you some cool stuff in Minecraft, and ...
Police searching Willunga property of Dale McCauley, who disappeared in 1998 and is believed to have ...POLICE are searching a Willunga house, and a dam at a nearby property, over the disappearance and suspected murder of a man 17 years ago.
Missing Malaysia Airlines jet: Searching from space may helpHigh-definition satellite imagery would seem to be an ideal tool to use in the multinational hunt for a passenger jet that simply vanished nearly ...
Police searching for missing 13-year-old Bunbury girl Zadie HawkinsPolice are concerned for a missing 13-year-old Bunbury girl who been missing since Sunday.
Family searching for man who disappeared Friday in ColumbusRelatives say Joey LaBute was at the Union Café just after 12:30 a.m. March 5 before disappearing.
Resources last updated: 3/30/2016 4:33:32 AM