|
|
ntpd and 2 address
Hello,
my NTP server works fine, but only on public IP address. Few servers have only private IP (10.0.0.0/24) and these cant connect to 10.0.0.4.
ntpdate[11642]: no server suitable for synchronization found
server config:
tinker panic 4000
server tik.cesnet.cz
restrict tik.cesnet.cz
....
driftfile /etc/ntp/drift
restrict default noquery notrust nomodify
restrict 127.0.0.1
restrict xx.xx.xx.0 netmask 255.255.255.0 notrap nomodify noquery
restrict 10.0.0.0 netmask 255.255.255.0 notrap nomodify noquery
client config:
tinker panic 4000
server 10.0.0.4 #or server pu.bl.ic.ip
driftfile /etc/ntp/drift
restrict default noquery notrust nomodify
restrict 127.0.0.1
restrict 10.0.0.4
client config is same for machines with public IP and only with private IP address
but only public IP is working
no problem in firewall (same for public and for private network)
anyone help me please?
regards
Martin Korous
ntp-4.2.0-i486-1
_______________________________________________
questions mailing list
questions@lists.ntp.isc.org
https://lists.ntp.isc.org/mailman/listinfo/questions
|
|
0
|
|
|
|
Reply
|
 Mortals (1)
|
4/10/2007 2:17:42 PM |
|
What is the result of running 'ntpq -p 10.0.0.4' from one of the client
boxes?
H
|
|
|
0
|
|
|
|
Reply
|
 Harlan
|
4/12/2007 5:10:31 AM
|
|
|
1 Replies
229 Views
(page loaded in 0.036 seconds)
Similiar Articles: ntpd and 2 address - comp.protocols.time.ntpHello, my NTP server works fine, but only on public IP address. Few servers have only private IP (10.0.0.0/24) and these cant connect to 10.0.0.4. nt... bind ntpd to a specific adress - comp.protocols.time.ntp ...Hi, I am trying to set up a jail environment on one of my FreeBSD Servers and I am asking if it is possible to bind ntpd to a specific IP address ???... ntpd IPv6 support on Windows? - comp.protocols.time.ntpntpd and 2 address - comp.protocols.time.ntp ntpd IPv6 support on Windows? - comp.protocols.time.ntp ntpd and 2 address - comp.protocols.time.ntp ntpd IPv6 support on ... Test ntpd performance - comp.protocols.time.ntpntpd and 2 address - comp.protocols.time.ntp Test ntpd performance - comp.protocols.time.ntp ntpd and 2 address - comp.protocols.time.ntp Test ntpd performance - comp ... ntpd on AIX6.1 does not start - comp.protocols.time.ntp... error on startup: /temp/ntp-4.2.6p3 $> ./ntpd/ntpd -4 -n -d -d ntpd 4.2.6p3@1 ... the deamon works, but the signal quality on the server location is poor .... ntpd, boot time, and hot plugging - comp.protocols.time.ntp ...> 2) start ntpd > 3) start time-dependent services > > It would ... So, when your IP address changes, you have to restart ntpd. You have the same problem if you ... NTPd with proxy - comp.protocols.time.ntpHi, It's possible to configure ntpd to connect to a ntp ... If you don't have this possibility, contact your proxy ... old messages on this mailing list and i've confused two ... Bind Address - comp.protocols.time.ntp> I have a few ethX card and I want to set up ntpd only to eth0 ip > address and lo interface. Use restrict lines in your /etc/ntp.conf to control access. Bad File Descriptor - comp.protocols.time.ntpMy Linux system (on which runs ntpd-2.4.0) has two links to Internet: one ... elsewhere, you can do IP address masquerading down stream so that > ntpd sees a fixed address. Interface IP address Change. - comp.protocols.time.ntp... My question is How can I make NTP automatically detect this change and >>>>> rebind >>>>> upon the change in the IP address of the interface ? >>> Since 4.2.4 ntpd ... ntpd and 2 address - comp.protocols.time.ntp | Computer GroupHello, my NTP server works fine, but only on public IP address. Few servers have only private IP (10.0.0.0/24) and these cant connect to 10.0.0.4. nt... ntp.org: Home of the Network Time ProtocolThe content at www.ntp.org is in the public domain, but contains some works copyrighted by other authors. Please contact webmaster@ntp.org for more information. 7/20/2012 10:00:11 PM
|
|
|
|
|
|
|
|
|
Search |
Post Question |
Groups |
Stream |
About |
Register
2 followers. 