2 NICs problem in SCO Open Server 5.0.5
Hi,
I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24 and
everything was OK. I installed second card ( the same type - 3COM 905B) and
configured IP as 192.168.1.1/24. After kernel relink and boot I can not ping
any machine in 192.168.1.0/24 network. I checked all physical connections,
routing, etc. Strange thing is that I noticed, that both network interfaces
have the same MAC address. If I run ifconfig -a, I see:
net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255
perf. params: recv size: 24576; send size: 24576; full-size frames:
1
ether 00:50:04:07:93:d6
net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255
perf. params: recv size: 24576; send size: 24576; full-size frames:
1
ether 00:50:04:07:93:d6
What did I do wrong? Have you ever seen and solved this problem?
Thanks for any advice.
Wojtek.
wkorgol
comp.unix.sco.misc
3925 articles. 
0 followers.
7 Replies
697 Views
Wojtek Korg�l wrote: > Hi, > > I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24 and > everything was OK. I installed second card ( the same type - 3COM 905B) and > configured IP as 192.168.1.1/24. After kernel relink and boot I can not ping > any machine in 192.168.1.0/24 network. I checked all physical connections, > routing, etc. Strange thing is that I noticed, that both network interfaces > have the same MAC address. If I run ifconfig -a, I see: > > net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255 > perf. params: recv size: 24576; send size: 24576; full-size frames: > 1 > ether 00:50:04:07:93:d6 > > net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255 > perf. params: recv size: 24576; send size: 24576; full-size frames: > 1 > ether 00:50:04:07:93:d6 > > What did I do wrong? What exactly did you type in when configuring the NICs? > Have you ever seen and solved this problem? No, so consider this as moral support only. > Thanks for any advice. I'd suspect that the OSR5 drivers are confused and are seeing the same card twice. I'd do one or all of ... 1) Boot a knoppix CD and see what *it* thinks the MAC addresses are of the cards. 2) Peek inside the box and read the Mac addresses off the labels on the NIC 3) Use (bootable?) NIC-diagnostics diskette provided by 3COM 4) Uninstall both cards (in OSR5 not physically) and reinstall, paying careful attention to any shared resources like IRQs. YMMV
scobloke2Wojtek Korg?l enscribed: | | I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24 and | everything was OK. I installed second card ( the same type - 3COM 905B) and | configured IP as 192.168.1.1/24. After kernel relink and boot I can not ping | any machine in 192.168.1.0/24 network. I checked all physical connections, | routing, etc. Strange thing is that I noticed, that both network interfaces | have the same MAC address. If I run ifconfig -a, I see: | | net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 | inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255 | perf. params: recv size: 24576; send size: 24576; full-size frames: | 1 | ether 00:50:04:07:93:d6 | | net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 | inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255 | perf. params: recv size: 24576; send size: 24576; full-size frames: | 1 | ether 00:50:04:07:93:d6 | | What did I do wrong? Have you ever seen and solved this problem? | Thanks for any advice. You don't need various 3rd party tools as someone suggested, a good start would be to run basic system information tools. For a quick check: # hwconfig Do both cards show the same addresses? 2 - 905B's on 5.0.5 would probably display as: name=e3H base=0xD800 offset=0x7F vec=11 dma=- 3Com 3C90x, unit=0 name=e3H base=0xE000 offset=0x7F vec=9 dma=- 3Com 3C90x, unit=1 For a detailed check: # hw -mr pci Is the information the same for both cards? If the information is the same, the same card is configured with both ip addresses. -- ========================================================================== Tom Parsons tom@tegan.com ==========================================================================
cis1
Uzytkownik "Tom Parsons" <cis@tegan.com> napisal w wiadomosci
news:20031203070414.28275@tegan.com...
> Wojtek Korg?l enscribed:
> |
> | I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24
and
> | everything was OK. I installed second card ( the same type - 3COM 905B)
and
> | configured IP as 192.168.1.1/24. After kernel relink and boot I can not
ping
> | any machine in 192.168.1.0/24 network. I checked all physical
connections,
> | routing, etc. Strange thing is that I noticed, that both network
interfaces
> | have the same MAC address. If I run ifconfig -a, I see:
> |
> | net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> | inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255
> | perf. params: recv size: 24576; send size: 24576; full-size
frames:
> | 1
> | ether 00:50:04:07:93:d6
> |
> | net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> | inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255
> | perf. params: recv size: 24576; send size: 24576; full-size
frames:
> | 1
> | ether 00:50:04:07:93:d6
> |
> | What did I do wrong? Have you ever seen and solved this problem?
> | Thanks for any advice.
>
> You don't need various 3rd party tools as someone suggested, a good start
> would be to run basic system information tools.
>
> For a quick check:
> # hwconfig Do both cards show the same addresses?
>
> 2 - 905B's on 5.0.5 would probably display as:
>
> name=e3H base=0xD800 offset=0x7F vec=11 dma=- 3Com 3C90x, unit=0
> name=e3H base=0xE000 offset=0x7F vec=9 dma=- 3Com 3C90x, unit=1
>
> For a detailed check:
> # hw -mr pci Is the information the same for both cards?
>
> If the information is the same, the same card is configured with both
> ip addresses.
> --
> ==========================================================================
> Tom Parsons tom@tegan.com
> ==========================================================================
Hi,
hwconfig returns:
name=e3H base=0x6400 offset=0x7F vec=10 dma=- 3Com 3c90x/3c980, unit=0
name=e3H base=0x5000 offset=0x7F vec=15 dma=- 3Com 3c90x/3c980, unit=1
hw -mr pci for these cards returns diffrent values as shown below, so my
system recognizes 2 diffrent cards, maybe /dev/net0 and /dev/net1 points to
the same device. /dev/net0 and /dev/net1 have the same major and minor
numbers. I still do not know how to fix it.
DeviceNum: 15
Function: 0
Bus: 0
VendorId: 3Com Corporation
DeviceId: 0x9055
RevId: 0x64
Command: 0x0107 Memory Enabled, I/O Enabled
Status: 0x0210
ClassCode: 0x020000 Ethernet controller
CacheLineSize: 8 32 bit words
LatencyTimer: 0x50
HeaderType: 0x00 Single-function, Standard encoding
BaseAddr[0]: I/O 0x5000
BaseAddr[1]: Memory 0x50000000, 32 bit space
SubsysVendorID: 3Com Corporation
SubsystemID: 0x9055
InterruptLine: IRQ-15
Index: 9
DeviceNum: 4
Function: 0
Bus: 1
VendorId: 3Com Corporation
DeviceId: 0x9200
RevId: 0x74
Command: 0x0107 Memory Enabled, I/O Enabled
Status: 0x0210
ClassCode: 0x020000 Ethernet controller
CacheLineSize: 8 32 bit words
LatencyTimer: 0x50
HeaderType: 0x00 Single-function, Standard encoding
BaseAddr[0]: I/O 0x6400
BaseAddr[1]: Memory 0x50101000, 32 bit space
SubsysVendorID: 3Com Corporation
SubsystemID: 0x1000
InterruptLine: IRQ-10
Regards,
Wojtek
Wojtek Korg?l enscribed:
|
| Uzytkownik "Tom Parsons" <cis@tegan.com> napisal w wiadomosci
| news:20031203070414.28275@tegan.com...
| > Wojtek Korg?l enscribed:
| > |
| > | I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24
| and
| > | everything was OK. I installed second card ( the same type - 3COM 905B)
| and
| > | configured IP as 192.168.1.1/24. After kernel relink and boot I can not
| ping
| > | any machine in 192.168.1.0/24 network. I checked all physical
| connections,
| > | routing, etc. Strange thing is that I noticed, that both network
| interfaces
| > | have the same MAC address. If I run ifconfig -a, I see:
| > |
| > | net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
| > | inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255
| > | perf. params: recv size: 24576; send size: 24576; full-size
| frames:
| > | 1
| > | ether 00:50:04:07:93:d6
| > |
| > | net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
| > | inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255
| > | perf. params: recv size: 24576; send size: 24576; full-size
| frames:
| > | 1
| > | ether 00:50:04:07:93:d6
| > |
| > | What did I do wrong? Have you ever seen and solved this problem?
| > | Thanks for any advice.
| >
| > You don't need various 3rd party tools as someone suggested, a good start
| > would be to run basic system information tools.
| >
| > For a quick check:
| > # hwconfig Do both cards show the same addresses?
| >
| > 2 - 905B's on 5.0.5 would probably display as:
| >
| > name=e3H base=0xD800 offset=0x7F vec=11 dma=- 3Com 3C90x, unit=0
| > name=e3H base=0xE000 offset=0x7F vec=9 dma=- 3Com 3C90x, unit=1
| >
| > For a detailed check:
| > # hw -mr pci Is the information the same for both cards?
| >
| > If the information is the same, the same card is configured with both
| > ip addresses.
|
| hwconfig returns:
| name=e3H base=0x6400 offset=0x7F vec=10 dma=- 3Com 3c90x/3c980, unit=0
| name=e3H base=0x5000 offset=0x7F vec=15 dma=- 3Com 3c90x/3c980, unit=1
|
| hw -mr pci for these cards returns diffrent values as shown below, so my
| system recognizes 2 diffrent cards, maybe /dev/net0 and /dev/net1 points to
| the same device. /dev/net0 and /dev/net1 have the same major and minor
| numbers. I still do not know how to fix it.
|
| DeviceNum: 15
| Function: 0
| Bus: 0
| VendorId: 3Com Corporation
| DeviceId: 0x9055
| RevId: 0x64
| Command: 0x0107 Memory Enabled, I/O Enabled
| Status: 0x0210
| ClassCode: 0x020000 Ethernet controller
| CacheLineSize: 8 32 bit words
| LatencyTimer: 0x50
| HeaderType: 0x00 Single-function, Standard encoding
| BaseAddr[0]: I/O 0x5000
| BaseAddr[1]: Memory 0x50000000, 32 bit space
| SubsysVendorID: 3Com Corporation
| SubsystemID: 0x9055
| InterruptLine: IRQ-15
|
| Index: 9
| DeviceNum: 4
| Function: 0
| Bus: 1
| VendorId: 3Com Corporation
| DeviceId: 0x9200
| RevId: 0x74
| Command: 0x0107 Memory Enabled, I/O Enabled
| Status: 0x0210
| ClassCode: 0x020000 Ethernet controller
| CacheLineSize: 8 32 bit words
| LatencyTimer: 0x50
| HeaderType: 0x00 Single-function, Standard encoding
| BaseAddr[0]: I/O 0x6400
| BaseAddr[1]: Memory 0x50101000, 32 bit space
| SubsysVendorID: 3Com Corporation
| SubsystemID: 0x1000
| InterruptLine: IRQ-10
net0 and net1 should not have the same major/minor numbrs. See where the
system thinks they should be. This would govern the best way to fix the
problem.
# grep net /etc/conf/cf.d/mdevice
You should see something like this, with the sixth column showing the
minor number. Post the output.
net0 I iSc net0 0 123 1 256 -1
net1 - iSc net1 0 126 1 256 -1
--
==========================================================================
Tom Parsons tom@tegan.com
==========================================================================
> | Uzytkownik "Tom Parsons" <cis@tegan.com> napisal w wiadomosci > | news:20031203070414.28275@tegan.com... > | > Wojtek Korg?l enscribed: > | > | > | > | I had a SCO box with 1 card ( 3COM 905B ) installed with IP 10.0.1.30/24 > | and > | > | everything was OK. I installed second card ( the same type - 3COM 905B) > | and > | > | configured IP as 192.168.1.1/24. After kernel relink and boot I can not > | ping > | > | any machine in 192.168.1.0/24 network. I checked all physical > | connections, > | > | routing, etc. Strange thing is that I noticed, that both network > | interfaces > | > | have the same MAC address. If I run ifconfig -a, I see: > | > | > | > | net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > | > | inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255 > | > | perf. params: recv size: 24576; send size: 24576; full-size > | frames: > | > | 1 > | > | ether 00:50:04:07:93:d6 > | > | > | > | net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > | > | inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255 > | > | perf. params: recv size: 24576; send size: 24576; full-size > | frames: > | > | 1 > | > | ether 00:50:04:07:93:d6 > | > | > | > | What did I do wrong? Have you ever seen and solved this problem? > | > | Thanks for any advice. > | > > | > You don't need various 3rd party tools as someone suggested, a good start > | > would be to run basic system information tools. > | > > | > For a quick check: > | > # hwconfig Do both cards show the same addresses? > | > > | > 2 - 905B's on 5.0.5 would probably display as: > | > > | > name=e3H base=0xD800 offset=0x7F vec=11 dma=- 3Com 3C90x, unit=0 > | > name=e3H base=0xE000 offset=0x7F vec=9 dma=- 3Com 3C90x, unit=1 > | > > | > For a detailed check: > | > # hw -mr pci Is the information the same for both cards? > | > > | > If the information is the same, the same card is configured with both > | > ip addresses. > | > | hwconfig returns: > | name=e3H base=0x6400 offset=0x7F vec=10 dma=- 3Com 3c90x/3c980, unit=0 > | name=e3H base=0x5000 offset=0x7F vec=15 dma=- 3Com 3c90x/3c980, unit=1 > | > | hw -mr pci for these cards returns diffrent values as shown below, so my > | system recognizes 2 diffrent cards, maybe /dev/net0 and /dev/net1 points to > | the same device. /dev/net0 and /dev/net1 have the same major and minor > | numbers. I still do not know how to fix it. > | > | DeviceNum: 15 > | Function: 0 > | Bus: 0 > | VendorId: 3Com Corporation > | DeviceId: 0x9055 > | RevId: 0x64 > | Command: 0x0107 Memory Enabled, I/O Enabled > | Status: 0x0210 > | ClassCode: 0x020000 Ethernet controller > | CacheLineSize: 8 32 bit words > | LatencyTimer: 0x50 > | HeaderType: 0x00 Single-function, Standard encoding > | BaseAddr[0]: I/O 0x5000 > | BaseAddr[1]: Memory 0x50000000, 32 bit space > | SubsysVendorID: 3Com Corporation > | SubsystemID: 0x9055 > | InterruptLine: IRQ-15 > | > | Index: 9 > | DeviceNum: 4 > | Function: 0 > | Bus: 1 > | VendorId: 3Com Corporation > | DeviceId: 0x9200 > | RevId: 0x74 > | Command: 0x0107 Memory Enabled, I/O Enabled > | Status: 0x0210 > | ClassCode: 0x020000 Ethernet controller > | CacheLineSize: 8 32 bit words > | LatencyTimer: 0x50 > | HeaderType: 0x00 Single-function, Standard encoding > | BaseAddr[0]: I/O 0x6400 > | BaseAddr[1]: Memory 0x50101000, 32 bit space > | SubsysVendorID: 3Com Corporation > | SubsystemID: 0x1000 > | InterruptLine: IRQ-10 > > net0 and net1 should not have the same major/minor numbrs. See where the > system thinks they should be. This would govern the best way to fix the > problem. > > # grep net /etc/conf/cf.d/mdevice > > You should see something like this, with the sixth column showing the > minor number. Post the output. > > net0 I iSc net0 0 123 1 256 -1 > net1 - iSc net1 0 126 1 256 -1 > > -- > ========================================================================== > Tom Parsons tom@tegan.com > ========================================================================== Hi, In my systems mdevice contains: net1 I iSc net1 0 86 1 256 -1 net0 - iSc net0 0 95 1 256 -1 and in /dev I see: crw-rw-rw- 1 root root 40, 86 Mar 7 2000 net0 crw-rw-rw- 1 root root 40, 86 Sep 28 2000 net1 I suppose that system did not create proper device for second card. Can I simply remove /dev/net1 and recreate it with 95 as minor number? This SCO box is critical, so I would like not to experiment. Regards, Wojtek
In article <bqkdco$hq7$1@inews.gazeta.pl>, Wojtek Korg�l <wkorgol@nospam.gazeta.pl> wrote: >I had a SCO box with 1 card ( 3COM 905B ) installed with IP >10.0.1.30/24 and everything was OK. I installed second card ( >the same type - 3COM 905B) and configured IP as 192.168.1.1/24. >After kernel relink and boot I can not ping any machine in >192.168.1.0/24 network. I checked all physical connections, >routing, etc. Strange thing is that I noticed, that both network >interfaces have the same MAC address. If I run ifconfig -a, I >see: [NIC info deleted. wjv] .... >What did I do wrong? Have you ever seen and solved this problem? >Thanks for any advice. Did you add the appropriate route. If your default route it still using the 10.0.1.0 network and you have not added a route for t 192.168.1.0 network to use 192.168.1.1 as the gateway for that network you will never get where you want to go. You didn't mention if you did this or not. What does the output of netstat -rn show as gateway. Bill -- Bill Vermillion - bv @ wjv . com
bv23Wojtek Korg?l enscribed: | > | Uzytkownik "Tom Parsons" <cis@tegan.com> napisal w wiadomosci | > | news:20031203070414.28275@tegan.com... | > | > Wojtek Korg?l enscribed: | > | > | | > | > | I had a SCO box with 1 card ( 3COM 905B ) installed with IP | 10.0.1.30/24 | > | and | > | > | everything was OK. I installed second card ( the same type - 3COM | 905B) | > | and | > | > | configured IP as 192.168.1.1/24. After kernel relink and boot I can | not | > | ping | > | > | any machine in 192.168.1.0/24 network. I checked all physical | > | connections, | > | > | routing, etc. Strange thing is that I noticed, that both network | > | interfaces | > | > | have the same MAC address. If I run ifconfig -a, I see: | > | > | | > | > | net1: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 | > | > | inet 10.0.1.30 netmask ffffff00 broadcast 10.0.1.255 | > | > | perf. params: recv size: 24576; send size: 24576; full-size | > | frames: | > | > | 1 | > | > | ether 00:50:04:07:93:d6 | > | > | | > | > | net0: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 | > | > | inet 192.168.1.1 netmask ffffff00 broadcast 192.168.1.255 | > | > | perf. params: recv size: 24576; send size: 24576; full-size | > | frames: | > | > | 1 | > | > | ether 00:50:04:07:93:d6 | > | > | | > | > | What did I do wrong? Have you ever seen and solved this problem? | > | > | Thanks for any advice. | > | > | > | > You don't need various 3rd party tools as someone suggested, a good | start | > | > would be to run basic system information tools. | > | > | > | > For a quick check: | > | > # hwconfig Do both cards show the same addresses? | > | > | > | > 2 - 905B's on 5.0.5 would probably display as: | > | > | > | > name=e3H base=0xD800 offset=0x7F vec=11 dma=- 3Com 3C90x, unit=0 | > | > name=e3H base=0xE000 offset=0x7F vec=9 dma=- 3Com 3C90x, unit=1 | > | > | > | > For a detailed check: | > | > # hw -mr pci Is the information the same for both cards? | > | > | > | > If the information is the same, the same card is configured with both | > | > ip addresses. | > | | > | hwconfig returns: | > | name=e3H base=0x6400 offset=0x7F vec=10 dma=- 3Com 3c90x/3c980, unit=0 | > | name=e3H base=0x5000 offset=0x7F vec=15 dma=- 3Com 3c90x/3c980, unit=1 | > | | > | hw -mr pci for these cards returns diffrent values as shown below, so my | > | system recognizes 2 diffrent cards, maybe /dev/net0 and /dev/net1 points | to | > | the same device. /dev/net0 and /dev/net1 have the same major and minor | > | numbers. I still do not know how to fix it. | > | | > | DeviceNum: 15 | > | Function: 0 | > | Bus: 0 | > | VendorId: 3Com Corporation | > | DeviceId: 0x9055 | > | RevId: 0x64 | > | Command: 0x0107 Memory Enabled, I/O Enabled | > | Status: 0x0210 | > | ClassCode: 0x020000 Ethernet controller | > | CacheLineSize: 8 32 bit words | > | LatencyTimer: 0x50 | > | HeaderType: 0x00 Single-function, Standard encoding | > | BaseAddr[0]: I/O 0x5000 | > | BaseAddr[1]: Memory 0x50000000, 32 bit space | > | SubsysVendorID: 3Com Corporation | > | SubsystemID: 0x9055 | > | InterruptLine: IRQ-15 | > | | > | Index: 9 | > | DeviceNum: 4 | > | Function: 0 | > | Bus: 1 | > | VendorId: 3Com Corporation | > | DeviceId: 0x9200 | > | RevId: 0x74 | > | Command: 0x0107 Memory Enabled, I/O Enabled | > | Status: 0x0210 | > | ClassCode: 0x020000 Ethernet controller | > | CacheLineSize: 8 32 bit words | > | LatencyTimer: 0x50 | > | HeaderType: 0x00 Single-function, Standard encoding | > | BaseAddr[0]: I/O 0x6400 | > | BaseAddr[1]: Memory 0x50101000, 32 bit space | > | SubsysVendorID: 3Com Corporation | > | SubsystemID: 0x1000 | > | InterruptLine: IRQ-10 | > | > net0 and net1 should not have the same major/minor numbrs. See where the | > system thinks they should be. This would govern the best way to fix the | > problem. | > | > # grep net /etc/conf/cf.d/mdevice | > | > You should see something like this, with the sixth column showing the | > minor number. Post the output. | > | > net0 I iSc net0 0 123 1 256 -1 | > net1 - iSc net1 0 126 1 256 -1 | > | | In my systems mdevice contains: | net1 I iSc net1 0 86 1 256 -1 | net0 - iSc net0 0 95 1 256 -1 | and in /dev I see: | crw-rw-rw- 1 root root 40, 86 Mar 7 2000 net0 | crw-rw-rw- 1 root root 40, 86 Sep 28 2000 net1 | | I suppose that system did not create proper device for second card. Can I | simply remove /dev/net1 and recreate it with 95 as minor number? This SCO | box is critical, so I would like not to experiment. That's very unlikely. More likely a human did it. Caveat: The way I'm going to recommend fixing this is not the way I would do it because I can't be there to fix any problems that might occur with my method. I've had some odd relinking issues with multiple 905 cards and 5.0.5. I would: Remove the second network card, rebuild the kernel, making sure to let it rebuild the environment then reboot. Verify the major/minor numbers for net0 and net1 are 40,86 and 40,95. If they are now correct, reinstall the second network card, rebuild and reboot. If they are not correct, post the output of these because something strange is happening and we need to find the cause. # grep "net" /etc/conf/cf.d/mdevice # grep "net" /etc/conf/cf.d/conf.c -- ========================================================================== Tom Parsons tom@tegan.com ==========================================================================
Similar Artilces:
error while installing on-board NIC on Proliant 1600 server in SCO Open Server 5.0.5
dear all, While installing the EFS, when I configure the TCP/IP then i get the messages while relinking the kernel. i encountered the message when after installing the Advanced File and Print Server in SCO Open Server 5 i rebooted the server Compaq Proliant 1600 i get the message /dev/nbcots: invalid transport provider name /dev/netbeui: invalid transport provider name this problem prevents me from printing thru UNIX on windows pcs. i m not able to print on printers attached to windows pcs. one another message also occurs while relinking kernel: /etc/conf/bin/idmknod: driver ida not a character special device but it gives that the kernel has been relinked successfully. another error is: /opt/K/SCO/link/1.1.1Eb/etc/conf/bin/idmknod: driver ida is not a character special device. another error message while booting is: /dev/datalink : no such file or directory nbelink : no such file or directory starting netbios: nbd : can't open NETBIOS device : no such file or directory. these problems prevent me from starting Advanced File and Print services on the server. please help -- Posted via http://dbforums.com ...
SCO Open Server 5.0.6 versus 5.0.4
Hi, Anybody can point me to info or can state if there is a performance improvement from running 5.0.6 versus 5.0.4. Application is database access centered. Regards, Marian news wrote: > Hi, > Anybody can point me to info or can state if there is a performance > improvement from running 5.0.6 versus 5.0.4. Application is database access > centered. I don't think you are going to get a useful answer. Let's assume that I could authoritatively say that 5.0.6 has performance related improvements over .4 in certain areas. I can't recall if it does or doesn't, but the release notes would surely mention any. But so what? What does that say about YOUR application? Do we know where its performance issuees are now? Nope. We could assume it's probably disk bound, because that's a pretty safe assumption most any time, but even if true, what have you done for better or worse in that regard already? Maybe this is an Oracle database and you have it running on a RAID 5 system. As that's usually going to be a bad idea, you could gain nothing even if 5.0.6 did otherwise provide features that would otherwise improve your lot. Maybe you have the whole thing improperly tuned. Maybe you have it so perfectly tuned that an upgrade would make it worse because everything is so critically balanced to what you have now.. There are plenty of good reasons to upgrade to 5.0.6/7. If that's what you are lookimg for (a reason to sell the idea to ...
NFS SCo 5.0.5 with SCO 6.0.0
Hi everybody, I have a folder on SCO 5.0.5 server shared through NFS with a new SCO 6.0.0 with MP2 server (converted from a SCO 5.0.6 version). Before conversion file locks (over network) on this folder works well (eg from server SCO 5.0.6 I was able to see locks generated from SCO 5.0.5 box and viceversa), now with SCO 6.0.0 does not work ! I see that on SCO 6.0.0 the lockd daemon is active .. so it should work ... Please can you help me ? Thanks Cuffiette ...
Problem using cron on SCO 5.0.5 #2
Hi, I have a problem using cron on SCO 5.0.5.. Jobs have been scheduled for more than 20hrs. Problem is after executing the jobs for 6 to 7 hrs the cron stops functioning. I need to reboot Sco Unix in order for the cron to be started. This is a serious problem for me as i need to take databases tran's log dumps every hour, and definately its wrong way to reboot the server for cron to be started. Waiting for an answer and thanx. Regards Nitin Nitin Shinde typed (on Fri, Jul 25, 2003 at 03:35:48AM -0700): | Hi, | I have a problem using cron on SCO 5.0.5.. Jobs have been scheduled | for more than 20hrs. Problem is after executing the jobs for 6 to 7 | hrs the cron stops | functioning. I need to reboot Sco Unix in order for the cron to be | started. | This is a serious problem for me as i need to take databases tran's | log dumps every hour, and definately its wrong way to reboot the | server for cron to be started. | Waiting for an answer and thanx. If cron isn't running, why don't you just type /etc/cron? -- JP ...
Looking for precompiled 'rsync" for SCO 5.0.5, 5.0.6 and 5.0.7
I was recommended to use 'rsync' for multi-site transfers. But I have come to find that "rsync" does not exist already in OpenServer 5.0.5, 5.0.6 and 5.0.7. You can only get the "source" files which you "must" compile in order to create the "rsync." These seems to require that you compile these on every level of OpenServer you need. Where / how can I get the 'rsync' binaries already compiled for the levels I need? smlunatick typed (on Tue, Aug 18, 2009 at 11:10:53AM -0700): | I was recommended to use 'rsync' for multi-site transfers. But I have | come to find that "rsync" does not exist already in OpenServer 5.0.5, | 5.0.6 and 5.0.7. You can only get the "source" files which you "must" | compile in order to create the "rsync." These seems to require that | you compile these on every level of OpenServer you need. | | Where / how can I get the 'rsync' binaries already compiled for the | levels I need? Get a binary for OSR 5.0.7, and with oss646c, it should run on 5.0.4, 5.0.5, and 5.0.6. Binary afavilable on Brian White's page at www.aljex.com/bkw. -- JP On Aug 18, 7:37=A0pm, Jean-Pierre Radley <j...@jpr.com> wrote: > smlunatick typed (on Tue, Aug 18, 2009 at 11:10:53AM -0700): > | I was recommended to use 'rsync' for multi-site transfers. =A0But I hav= e > | come to find that "rsync" does not exist already in OpenSer...
sco 5.0.5. boot problems
Hi all Hi have a boot problem Several times when my SCO Server (running SCO Open server ver. 5.0.5.) boots it stops at the kernel line: G_hd_config and hangs. SO i have to switch off the server and power on another time then it starts normally without stoping. The server configuration is the following: Main board Supermicro with Adaptec 7980 dual channel CPU Xeon 550 Mhz. 256 Mb. RAM HD 9 Gb. SCSI Tandberg Backup Unit Thanks in advance Piertonio piertonio typed (on Fri, Jul 08, 2005 at 05:01:17PM +0200): | Hi all | Hi have a boot problem | Several times when my SCO Server (running SCO Open server ver. 5.0.5.) boots | it stops at the kernel line: G_hd_config and hangs. SO i have to switch off | the server and power on another time then it starts normally without | stoping. | The server configuration is the following: | | Main board Supermicro with Adaptec 7980 dual channel | CPU Xeon 550 Mhz. | 256 Mb. RAM | HD 9 Gb. SCSI | Tandberg Backup Unit You forgot to tell us which supplements and patches are applied. -- JP Sorry... here you are !! SCO OpenServer Enterprise System (ver 5.0.5m) ** ** Specialix SX serial support (ver 2.1.0) ** ** UDK Compatibility Module for OpenServer 5.0.5 (ver 5.0.5A) ** ** RS505A: Release Supplement for SCO OpenServer Release 5.0.5 (ver rs5 ** ** RS505A: Software Manager Supplement (ver rs505a) ** ** Year 2000 Supplement for RS505A (ver oss600a) ** ** Thank you Piertonio "Jean-Pi...
2 CPU license for SCO 5.0.5
Can anybody give me a 2 CPU license for SCO 5.0.5? Thanks. Avramenko Dmitry typed (on Sat, Jul 12, 2003 at 12:25:19AM +0400): | Can anybody give me a 2 CPU license for SCO 5.0.5? | "Give" ?? I'm a dealer and would be happy to sell one to you. -- JP ...
Problem Installing SCO OpenServer 5.0.5
Hi, Am trying to install SCO OpenServer 5.0.5 on a PIII with a 20GB Maxtor HD. I manage to install fine (no errors showing) and get UNIX to see the entire drive but upon reboot (removing the floppy and CD-ROM as instructed), instead of teh boot: prompt, it says NO OS. What am I doing wrong? Thanks, Don Don wrote: > > Hi, > > Am trying to install SCO OpenServer 5.0.5 on a PIII with a 20GB Maxtor > HD. I manage to install fine (no errors showing) and get UNIX to see > the entire drive but upon reboot (removing the floppy and CD-ROM as > instructed), instead of teh boot: prompt, it says NO OS. > > What am I doing wrong? > > Thanks, > Don Put this into www.groups.google and view the post by Bella: stamp dparam group:comp.unix.sco.misc -- Steve Fabac S.M. Fabac & Associates 816/765-1670 ...
Problem using cron on SCO 5.0.5
Hi, I have a problem using cron on Compaq Proliant ML-370 O/S SCO 5.0.5.. Jobs have been scheduled for more than 20hrs. Problem is after executing the jobs for 6 to 7 hrs the cron stops functioning. I need to reboot Sco Unix in order for the cron to be started. This is a serious problem for me as i need to take databases tran's log dumps every hour, and definately its wrong way to reboot the server for cron to be started. Waiting for an answer and thanx. Regards Nitin Nitin Shinde made comment on Fri Jul 25 09:53:24 2003 : > Hi, > I have a problem using cron on Compaq Proliant ML-370 O/S SCO 5.0.5.. > Jobs have been scheduled for more than 20hrs. Problem is after > executing the jobs for 6 to 7 hrs the cron stops functioning. I need > to reboot Sco Unix in order for the cron to be started. > This is a serious problem for me as i need to take databases tran's > log dumps every hour, and definately its wrong way to reboot the > server for cron to be started. > Waiting for an answer and thanx. What patches have been installed - specifically has the 'Cron Suppliment' oss642a been applied. -- ======================================================================== Tom Melvin tom@tkrh.demon.co.uk http://www.tkrh.demon.co.uk Veterinary Solutions Ltd Sysop Compuserve Unixforum ======================================================================== ...
SCO 5.0.5 dd / clone #2
Hi, I have an odd problem with one of my customer's SCO machines. Without going into a lot of detail and reasons for backup decisions, I have implemented a dd cloning of the master hard disk to a backup disk. That is to say my customer has 2 hard disks (in a caddy), the primary or master disk (hd00) and the clone or backup disk (hd10). A cron job wakes up twice daily and does a complete clone of the master disk to the backup / clone disk using dd. No great issue here as the entire disk (20Gb) takes about 24 minutes to complete. Now in Linux, this works great. If the master disk crashes for any reason, the customer simply re-boots their system and boots from the secondary drive whilst the primary is being repaired and all boots up fine and proper and no problems. However, the same process in SCO 5.0.5 seems to generate a completely corrupted disk. When I compare the master to the clone, you can see that the clone is completely a mess. I don't understand why this is the case with SCO but not with linux. As I'm doing a dd of the ENTIRE disk (a binary bit by bit copy), I don't understand why it doesn't work under sco. BTW - in SCO I don't boot from the secondary drive - I have to set it to the master drive first however, as per above the disk is so badly corrupted that the boot process will not work. The command I use is time dd if=/dev/hd00 of=/dev/hd10 bs=1451520 count=12529 (for SCO) time dd if=/dev/hda of=/dev/hdb bs=1451520 count=12529 (for l...
Problems with Business Basic on SCO 5.0.5
Hello, experts! I have an SCO Unix 5.0.5 server running Business Basic programs. When I try to connect my Wx PC clients to the Unix, via a Terminal Emulator, say Telnet or SCO TermLite in an ansi mode or vt100 mode, the Business Basic program interface appears to be "corrupted". It means that the sent characters look very untidy. So, I guess that the problem is with the bbx2 and not with the terminal emulator. I was seeking for some tips in this google group, and I just found that somebody put the following line in the .profile: stty rows 0 columns 0 xpixels 0 ypixels 0 Has anybody had a similar problem like mine? Many thanks! Rosa "Rosa2003" <rosa2003rosa@yahoo.com> wrote in message news:b2bd6daa.0308071139.5736a8e4@posting.google.com... > Hello, experts! > I have an SCO Unix 5.0.5 server running Business Basic programs. > When I try to connect my Wx PC clients to the Unix, via a Terminal > Emulator, say Telnet or SCO TermLite in an ansi mode or vt100 mode, > the Business Basic program interface appears to be "corrupted". It > means that the sent characters look very untidy. So, I guess that the > problem is with the bbx2 and not with the terminal emulator. I was > seeking for some tips in this google group, and I just found that > somebody put the following line in the .profile: > stty rows 0 columns 0 xpixels 0 ypixels 0 > > Has anybody had a similar problem like mine? > Many thanks!...
Trying to compile putty-0.60 on SCO UNIX 5.0.7 with GCC and SCO Dev
I am trying to compile putty downloaded from http://linux.softpedia.com/progDownload/PuTTY-Download-347.html but get the error below. gcc -g -O2 -Wall -Werror -DHAVE_CONFIG_H -DHAVE_X11 -DHAVE_X -DSYSV -Di386 -DS CO325 -D__SCO__ -DHAVE_XAW -DHAVE_SHAPE_EXT -DHAVE_SHAPE -DHAVE_SHM_EXT -DHAVE_X SHM -DHAVE_XCONVERTCASE -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr /include/atk-1.0 -I/usr/include/cairo -I/usr/include/pango-1.0 -I/usr/include/gl ib-2.0 -I/usr/lib/glib-2.0/include -I/usr/include/freetype2 -I/usr/X11R6/include -I.././ -I../charset/ -I../windows/ -I../unix/ -I../mac/ -I../macosx/ -c ../ proxy.c cc1: warnings being treated as errors .../proxy.c: In function `proxy_for_destination': .../proxy.c:315: warning: implicit declaration of function `strncasecmp' gmake: *** [proxy.o] Error 1 # My programming skill level tops out at ./configure and make. Searching for instances of strncasecmp in the putty working directory shows: /tmp/putty-0.60/unix # cd .. # find . -type f -print | xargs grep strncasecmp | less ../mac/stricmp.c:#define strncasecmp strnicmp ../mac/stricmp.c:strncasecmp(s1, s2, n) ../unix/unix.h:#define strnicmp strncasecmp (END) In unix/unix.h: #define DEFAULT_CODEPAGE 0xFFFF #define CP_UTF8 CS_UTF8 /* from libcharset */ #define strnicmp strncasecmp #define stricmp strcasecmp /* BSD-semantics version of signal(), and another helpful function */ void (*putty_signal(int sig, void (*func)(int)))(int); void block_si...
SYbase SQL & SCO OpenServer 5.0.4/5.0.5
Can somone help me with wich SQL versions runs on SCO OSR5.0.4 and SCO OSR 5.0.5? So your the customer SCO still has :-) Sorry.. Couldn't resist ! ASE 10.0.2 was certified on SCO OSR5.0.2 with OS patches SLS 422a, SLS 437a. It wasn't certified on anything higher. ASE 11.0.x was certified on 5.0.4, but nothing higher. Sybase doesn't support 10.x or 11.x any more ...
SCO's 5.0.7V on vmware server 2.0?
I see SCO has a downloadable 5.0.7 virtual machine in ISO form they boast will run on vmware, but the getting-started docs don't mention using vmware server 2.0 (the free version). Has anyone got this to work and if so how did you do it? It seems silly they don't document using it with the most popular versions of vmware. But it is SCO. And that yearly subscription? What were they thinking? That sure gives a lot of confidence--buying something that will quit on a yearly basis from a company that is going through bankruptcy. I am still using a 5.0.6 virtual machine I built three years ago for an old but required app, but it would be nice to go with something newer and better. OregonBob <oregonbob@gmail.com> wrote: > I see SCO has a downloadable 5.0.7 virtual machine in ISO form they > boast will run on vmware, but the getting-started docs don't mention > using vmware server 2.0 (the free version). Has anyone got this to > work and if so how did you do it? > > It seems silly they don't document using it with the most popular > versions of vmware. But it is SCO. (I worked at SCO for 15 years, and now VMware for 5 years; not speaking for either of them, of course...) As it turned out, VMware Server was never the most popular of VMware's products. It is now "end of life" (see small comment "*VMware Server was declared End Of Availability on January 2010. Support will be limited to Technical Guidance for the dura...
SCO Caldera v3.2.5.07 and Enterprise 5.0.7 3.2v5.0.7
I have 2 different software applications. We are considering moving both to a single server sunning sco. One vendor says they will only run on SCO caldera v 3.2.2.07 the other says they will only run on enterprise 5.0.7 3.2v5.0.7 I am confused, are these 2 different os's or just versions of the same os. Can someone enlighten me? gerard typed (on Fri, Oct 31, 2003 at 11:34:45AM -0800): | I have 2 different software applications. | We are considering moving both to a single server sunning sco. | One vendor says they will only run on SCO caldera v 3.2.2.07 There is no such version as 3.2.2.07. | the other says they will only run on enterprise 5.0.7 3.2v5.0.7 This is the latest release of SCO Openserver. -- JP gerardm@schurmans.com (gerard) wrote in message news:<97c6f92f.0310311134.2227a2c@posting.google.com>... > I have 2 different software applications. > We are considering moving both to a single server sunning sco. > One vendor says they will only run on SCO caldera v 3.2.2.07 > the other says they will only run on enterprise 5.0.7 3.2v5.0.7 > > I am confused, are these 2 different os's or just versions of the same os. > Can someone enlighten me? They both are the same, SCO UNIX 3.2V5.7 (enterprise). Abid ...
SCO 5.0.5/5.0.6 bios clock, time zone and synching
Hi All, Does SCO expect the BIOS clock to be set to UTC? Ive got a few SCO boxen spread across a couple of time zones and at the moment, the bios clocks in the servers are set to localtime not UTC. The timezone settings in SCO Admin are also wrong. I was under the impression *nix always expects the BIOS clock to be set to UTC and then the timezone settings in SCO tell the OS what the local time is. This does not seem to be the case for me. On a testing box, Ive set the BIOS clock to UTC, set the correct timezone in scoadmin but the date command in a root shell still gives the wrong time. Either the timezone information in scoadmin for my timezone is wrong and I need to set up an unlisted timezone (which I can do easily enough) or im missing something more fundamental here. Anyone care to wield a clue-bat? cheers John Smith wrote: > Does SCO expect the BIOS clock to be set to UTC? > > Ive got a few SCO boxen spread across a couple of time zones and at > the moment, the bios clocks in the servers are set to localtime not > UTC. > The timezone settings in SCO Admin are also wrong. > > I was under the impression *nix always expects the BIOS clock to be > set to UTC and then the timezone settings in SCO tell the OS what the > local time is. > This does not seem to be the case for me. > On a testing box, Ive set the BIOS clock to UTC, set the correct > timezone in scoadmin but the date command in a root shell still gives > the wro...
Using same SCO Openserver Enterprise 5.0.5. on 2 computers
Can I use the same SCO Openserver licence on two computers on the same network. I want to have a computer who is simply a clone of the other so I want to put the second computer on the network and make FTP transfert between the two computers. So if my "main" computer go down I can simply switch on the other computer. Thank you! "Mike" <michel.trudel@pentagone.com> wrote in message news:ede59572.0307291001.542e0fe0@posting.google.com... > Can I use the same SCO Openserver licence on two computers on the same > network. > I want to have a computer who is simply a clone of the other so I want > to put the second computer on the network and make FTP transfert > between the two computers. So if my "main" computer go down I can > simply switch on the other computer. > > Thank you! You'll get a repeated stream of console warnings from one or both machines that the same licenses are present on another machine on the network. These warnings will also be written to /usr/adm/syslog . Is this the only thing ? Is the syslog will be fill of those repeated messages or messages will appear once a day or something like that ? Is there any way to avoid those messages ? I've also heard that SCO can "stop running". Is there any "danger" ? Is there any lost of any functionnality ? Thanks! "Bob Bailin" <72027.3605@compuserve.com> wrote in message news:<bg8fhh$q81$2@ngspool-d02.news.a...
SCO 5.0.5 vs. 6.0
I'm having a new server built: SuperMicro P4SC8 Mother Board Intel P4 3.0Ghz 800 FSB 1GB CPU 73GB 10K 80 PIN SCSI Drive Sony 20/40GB DAT Drive SDT11000/BN DDS4 Adaptec 2010S Card for Mirroring Comtrol Rockport Card 99126-7 Is there any reason I should update my current version of SCO 5.0.5? Frank The following article is a recommendation from SCO when using P4 http://www.sco.com/ta/115963 "FrankS" <fshank@sbcglobal.net> wrote in message news:CqT_f.65026$H71.37215@newssvr13.news.prodigy.com... > I'm having a new server built: > > SuperMicro P4SC8 Mother Board > Intel P4 3.0Ghz 800 FSB 1GB CPU > 73GB 10K 80 PIN SCSI Drive > Sony 20/40GB DAT Drive SDT11000/BN DDS4 > > Adaptec 2010S Card for Mirroring > > Comtrol Rockport Card 99126-7 > > > > Is there any reason I should update my current version of SCO 5.0.5? > > > > Frank > > > > > > FrankS wrote: > I'm having a new server built: > > SuperMicro P4SC8 Mother Board > Intel P4 3.0Ghz 800 FSB 1GB CPU > 73GB 10K 80 PIN SCSI Drive > Sony 20/40GB DAT Drive SDT11000/BN DDS4 > > Adaptec 2010S Card for Mirroring > > Comtrol Rockport Card 99126-7 > > > > Is there any reason I should update my current version of SCO 5.0.5? Frank, OpenServer 5.0.5 is a retired product and is no longer generally supported by SCO. OpenServer 5.0.5 is not designed to work on P4 systems and y...
if time = 3 seconds, how do i set the values of the time steps 0,0.1,0.2,0.3,0.5,1.0,1.5,2.0,3.0,5.0 to -9999 from time =3 seconds
Hi I have 18 inputs (arrays) which contain certain statistics and if time = 3 seconds, set the values of time step 5.0 to -9999.0. I was wondering if there is an efficient way to do this without using a lot of case statements? Thank you. Hello AdrianT, it's not really clear to me what you want to do... I suspect: you have an array containing values and you want to output them with a fixed timing of 3 seconds: you should use a for loop autoindexing trough your array and sending the value to your indicator/output/whatever. Put a "wait for next multiple" into your for loop. Or do you want to have a minimum time delay of 3 seconds? Again use a for loop, get the time value and use a InRange&Coerce with minimum set to 3 seconds... Or you should explain more precisely what you need... Hi Thanks for that. Let me explain. The time may vary. Let me give an example. if time = 2.1, I want to set the time step's 3.0 and 5.0's values to -9999.0. if the time =0.1 seconds then I want to set 0.2,0.3, 0.5 etc values to -9999.0 etc .................................................................... Can you please help? Thank you. Hello TUDS, do you use different accounts/nicknames ? Well, that's easy, at least for a sorted array: Search for your time-value in the array (Threshold 1D array). Fill all elements from that index till the end with your "error...
Need NIC drivers/settings for SCO 5.0.5 on DELL pe2600
Hi All, An old customer that i dealt with many years ago called me saying = that their system had crashed and the people they were using were no help. = They did not have system backups but they had their DB backed up. I'm usi= ng their old dell server and their sco 5.0.5 disks and configured a new sys= tem. The one thing i can't find is NIC drivers. I have downloaded and ins= talled 2 sets of intel drivers but i have no idea what the card settings sh= ould be. After installing the drivers, running netconfig just gets me a li= st of cards i can select. any help would be greatly appreciated. thanks! On Friday, January 18, 2013 11:15:57 PM UTC-5, rdpcons...@gmail.com wrote: > Hi All, >=20 > An old customer that i dealt with many years ago called me sayin= g that their system had crashed and the people they were using were no help= .. They did not have system backups but they had their DB backed up. I'm u= sing their old dell server and their sco 5.0.5 disks and configured a new s= ystem. The one thing i can't find is NIC drivers. I have downloaded and i= nstalled 2 sets of intel drivers but i have no idea what the card settings = should be. After installing the drivers, running netconfig just gets me a = list of cards i can select. >=20 >=20 >=20 > any help would be greatly appreciated. >=20 > thanks! I ended up installing a 3com 3C905b and all is well. The intel driver i f...
Postgresql 7.4.1 Compile problem for SCO 5.0.5
I am trying to compile postgresql 7.4.1 for sco 5.0.5 and get the following error: "thread.c", line 269: error: undefined symbol: h_errno Any ideas? ../configure --with-libs=/usr/local/lib --with-includes=/usr/local/include herbie!/tmp/postgresql-7.4.1 # gmake gmake -C doc all gmake[1]: Entering directory `/tmp/postgresql-7.4.1/doc' gmake[1]: Nothing to be done for `all'. gmake[1]: Leaving directory `/tmp/postgresql-7.4.1/doc' gmake -C src all gmake[1]: Entering directory `/tmp/postgresql-7.4.1/src' gmake -C port all gmake[2]: Entering directory `/...
ttyp problem on Sco Open Server 5.04
I connect to my server trough a VT220 emulation PC and the server make a ttypX pseudo-terminal device. But when I logoff the emulation the server wrongly keep the ttypX without PID process. I sow this because when I shutdown the system It returned a message like "/etc/shutdown:3106 alarm call" and after 120 seconds it asked to me if I want to shutdown (y/n). The system then shutdown normally. Also the boot is correct and has no problems. What can I do to solve this problem? Thanks Marco This is the syslog file of my server with the telnetd error: [cut] Jul 9 08:43:56 scosysv telnetd[654]: ttloop: peer died: Unknown error Jul 9 08:44:22 scosysv telnetd[731]: ttloop: peer died: Unknown error Jul 9 08:44:42 scosysv telnetd[729]: ttloop: peer died: Unknown error Jul 9 08:45:17 scosysv telnetd[733]: can't find terminal control database entry for line ttyp0 Jul 9 08:46:43 scosysv telnetd[800]: can't find terminal control database entry for line ttyp0 Jul 9 08:49:28 scosysv telnetd[869]: can't find terminal control database entry for line ttyp1 Jul 9 08:50:03 scosysv telnetd[842]: can't find terminal control database entry for line ttyp0 Jul 9 09:57:19 scosysv telnetd[1084]: can't find terminal control database entry for line ttyp2 Jul 9 09:58:13 scosysv telnetd[1110]: can't find terminal control database entry for line ttyp2 Jul 9 10:00:50 scosysv telnetd[1056]: can't find terminal control database entry for line ttyp1 Jul 9 ...
SCO OpenServer 5.0.4/5.0.5 New Daylight Savings dates
Has anyone yet come up with a solution on changing older SCO OpenServer 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings dates starting this year?? I have looked around at SCO's site and they have an update to install on 5.0.7 systems that also indicate you should install new libc, etc Anyone know how to fix this on older SCO OpenServer releases?? Thanks for any help Scott Ullmann Telespectrum sullmann@telespectrum.com scooter typed (on Mon, Jan 22, 2007 at 12:37:58PM -0800): | Has anyone yet come up with a solution on changing older SCO OpenServer | 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings | dates starting this year?? | | I have looked around at SCO's site and they have an update to install | on 5.0.7 systems that also indicate you should install new libc, etc | | Anyone know how to fix this on older SCO OpenServer releases?? I'm in the EST timezone, and so I would edit /etc/TIMEZONE from: TZ=EST5EDT to: TZ=EST5EDT,M3,2,0/2,M11,1,0/2 -- JP ==> http://www.frappr.com/cusm <== On Jan 22, 4:24 pm, Jean-Pierre Radley <j...@jpr.com> wrote: > scooter typed (on Mon, Jan 22, 2007 at 12:37:58PM -0800): > | Has anyone yet come up with a solution on changing older SCO OpenServer > | 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings > | dates starting this year?? > | > | I have looked around at SCO's site and they have an update to install > | on 5.0.7 ...
3Com 3C905 XL PCI NIC on SCO 5.0.5 on Proliant 3000
hi there, following up on my install of Openserver 5.0.5 on a Compaq Proliant 3000, the only thing left to configre is the NIC. And I do this as follows: reboot boot up to X run network configuration manager add new LAN adapter choose 3Com Fast EtherLink XL PCI (3C905) When it asks for network driver configuration, i choose default (PCI bus:0, device:0, function:0) I presume this is ok, as it says '*' denotes conflict, and there is no * present. when asked to add protocol, i choose: SCO TCP/IP then add settings: machine name: propath ip: XX.XXX.XX.XX subnet mask: 255.255.0.0 broadcast mask: XX.255.255.255 domain name: mycompany.com tcp connections: 256 gateway: no advanced: gateway:no frame: ethernet-II i choose ok, save all. then am asked to relink kernel, i choose yes to all reboot machine(i know it is unnecessary to reboot but, i suppose its one of my windows hangups :)) and log on. run ifconfig -a and it gives me: lo atl0 (with various settings, including inet: 0.0.0.0) so there seems to be some prob;ems with the hardware. when i ping a known ip I get: no route to host any ideas? thanks in advance, bernard -- On 17 May 2004 12:50:20 GMT, bluNOboxSPAMthief <newsgroups-spambaiter@runningIHATEwithSPAMbulls.com> wrote: >hi there, > >following up on my install of Openserver >5.0.5 on a Compaq Proliant 3000, the only >thing left to configre is the NIC. > >And I do this as follows: > >reboot >boot up to X > &g...
dear all, While installing the EFS, when I configure the TCP/IP then i get the messages while relinking the kernel. i encountered the message when after installing the Advanced File and Print Server in SCO Open Server 5 i rebooted the server Compaq Proliant 1600 i get the message /dev/nbcots: invalid transport provider name /dev/netbeui: invalid transport provider name this problem prevents me from printing thru UNIX on windows pcs. i m not able to print on printers attached to windows pcs. one another message also occurs while relinking kernel: /etc/conf/bin/idmknod: driver ida not a character special device but it gives that the kernel has been relinked successfully. another error is: /opt/K/SCO/link/1.1.1Eb/etc/conf/bin/idmknod: driver ida is not a character special device. another error message while booting is: /dev/datalink : no such file or directory nbelink : no such file or directory starting netbios: nbd : can't open NETBIOS device : no such file or directory. these problems prevent me from starting Advanced File and Print services on the server. please help -- Posted via http://dbforums.com ...
SCO Open Server 5.0.6 versus 5.0.4
Hi, Anybody can point me to info or can state if there is a performance improvement from running 5.0.6 versus 5.0.4. Application is database access centered. Regards, Marian news wrote: > Hi, > Anybody can point me to info or can state if there is a performance > improvement from running 5.0.6 versus 5.0.4. Application is database access > centered. I don't think you are going to get a useful answer. Let's assume that I could authoritatively say that 5.0.6 has performance related improvements over .4 in certain areas. I can't recall if it does or doesn't, but the release notes would surely mention any. But so what? What does that say about YOUR application? Do we know where its performance issuees are now? Nope. We could assume it's probably disk bound, because that's a pretty safe assumption most any time, but even if true, what have you done for better or worse in that regard already? Maybe this is an Oracle database and you have it running on a RAID 5 system. As that's usually going to be a bad idea, you could gain nothing even if 5.0.6 did otherwise provide features that would otherwise improve your lot. Maybe you have the whole thing improperly tuned. Maybe you have it so perfectly tuned that an upgrade would make it worse because everything is so critically balanced to what you have now.. There are plenty of good reasons to upgrade to 5.0.6/7. If that's what you are lookimg for (a reason to sell the idea to ...
NFS SCo 5.0.5 with SCO 6.0.0
Hi everybody, I have a folder on SCO 5.0.5 server shared through NFS with a new SCO 6.0.0 with MP2 server (converted from a SCO 5.0.6 version). Before conversion file locks (over network) on this folder works well (eg from server SCO 5.0.6 I was able to see locks generated from SCO 5.0.5 box and viceversa), now with SCO 6.0.0 does not work ! I see that on SCO 6.0.0 the lockd daemon is active .. so it should work ... Please can you help me ? Thanks Cuffiette ...
Problem using cron on SCO 5.0.5 #2
Hi, I have a problem using cron on SCO 5.0.5.. Jobs have been scheduled for more than 20hrs. Problem is after executing the jobs for 6 to 7 hrs the cron stops functioning. I need to reboot Sco Unix in order for the cron to be started. This is a serious problem for me as i need to take databases tran's log dumps every hour, and definately its wrong way to reboot the server for cron to be started. Waiting for an answer and thanx. Regards Nitin Nitin Shinde typed (on Fri, Jul 25, 2003 at 03:35:48AM -0700): | Hi, | I have a problem using cron on SCO 5.0.5.. Jobs have been scheduled | for more than 20hrs. Problem is after executing the jobs for 6 to 7 | hrs the cron stops | functioning. I need to reboot Sco Unix in order for the cron to be | started. | This is a serious problem for me as i need to take databases tran's | log dumps every hour, and definately its wrong way to reboot the | server for cron to be started. | Waiting for an answer and thanx. If cron isn't running, why don't you just type /etc/cron? -- JP ...
Looking for precompiled 'rsync" for SCO 5.0.5, 5.0.6 and 5.0.7
I was recommended to use 'rsync' for multi-site transfers. But I have come to find that "rsync" does not exist already in OpenServer 5.0.5, 5.0.6 and 5.0.7. You can only get the "source" files which you "must" compile in order to create the "rsync." These seems to require that you compile these on every level of OpenServer you need. Where / how can I get the 'rsync' binaries already compiled for the levels I need? smlunatick typed (on Tue, Aug 18, 2009 at 11:10:53AM -0700): | I was recommended to use 'rsync' for multi-site transfers. But I have | come to find that "rsync" does not exist already in OpenServer 5.0.5, | 5.0.6 and 5.0.7. You can only get the "source" files which you "must" | compile in order to create the "rsync." These seems to require that | you compile these on every level of OpenServer you need. | | Where / how can I get the 'rsync' binaries already compiled for the | levels I need? Get a binary for OSR 5.0.7, and with oss646c, it should run on 5.0.4, 5.0.5, and 5.0.6. Binary afavilable on Brian White's page at www.aljex.com/bkw. -- JP On Aug 18, 7:37=A0pm, Jean-Pierre Radley <j...@jpr.com> wrote: > smlunatick typed (on Tue, Aug 18, 2009 at 11:10:53AM -0700): > | I was recommended to use 'rsync' for multi-site transfers. =A0But I hav= e > | come to find that "rsync" does not exist already in OpenSer...
sco 5.0.5. boot problems
Hi all Hi have a boot problem Several times when my SCO Server (running SCO Open server ver. 5.0.5.) boots it stops at the kernel line: G_hd_config and hangs. SO i have to switch off the server and power on another time then it starts normally without stoping. The server configuration is the following: Main board Supermicro with Adaptec 7980 dual channel CPU Xeon 550 Mhz. 256 Mb. RAM HD 9 Gb. SCSI Tandberg Backup Unit Thanks in advance Piertonio piertonio typed (on Fri, Jul 08, 2005 at 05:01:17PM +0200): | Hi all | Hi have a boot problem | Several times when my SCO Server (running SCO Open server ver. 5.0.5.) boots | it stops at the kernel line: G_hd_config and hangs. SO i have to switch off | the server and power on another time then it starts normally without | stoping. | The server configuration is the following: | | Main board Supermicro with Adaptec 7980 dual channel | CPU Xeon 550 Mhz. | 256 Mb. RAM | HD 9 Gb. SCSI | Tandberg Backup Unit You forgot to tell us which supplements and patches are applied. -- JP Sorry... here you are !! SCO OpenServer Enterprise System (ver 5.0.5m) ** ** Specialix SX serial support (ver 2.1.0) ** ** UDK Compatibility Module for OpenServer 5.0.5 (ver 5.0.5A) ** ** RS505A: Release Supplement for SCO OpenServer Release 5.0.5 (ver rs5 ** ** RS505A: Software Manager Supplement (ver rs505a) ** ** Year 2000 Supplement for RS505A (ver oss600a) ** ** Thank you Piertonio "Jean-Pi...
2 CPU license for SCO 5.0.5
Can anybody give me a 2 CPU license for SCO 5.0.5? Thanks. Avramenko Dmitry typed (on Sat, Jul 12, 2003 at 12:25:19AM +0400): | Can anybody give me a 2 CPU license for SCO 5.0.5? | "Give" ?? I'm a dealer and would be happy to sell one to you. -- JP ...
Problem Installing SCO OpenServer 5.0.5
Hi, Am trying to install SCO OpenServer 5.0.5 on a PIII with a 20GB Maxtor HD. I manage to install fine (no errors showing) and get UNIX to see the entire drive but upon reboot (removing the floppy and CD-ROM as instructed), instead of teh boot: prompt, it says NO OS. What am I doing wrong? Thanks, Don Don wrote: > > Hi, > > Am trying to install SCO OpenServer 5.0.5 on a PIII with a 20GB Maxtor > HD. I manage to install fine (no errors showing) and get UNIX to see > the entire drive but upon reboot (removing the floppy and CD-ROM as > instructed), instead of teh boot: prompt, it says NO OS. > > What am I doing wrong? > > Thanks, > Don Put this into www.groups.google and view the post by Bella: stamp dparam group:comp.unix.sco.misc -- Steve Fabac S.M. Fabac & Associates 816/765-1670 ...
Problem using cron on SCO 5.0.5
Hi, I have a problem using cron on Compaq Proliant ML-370 O/S SCO 5.0.5.. Jobs have been scheduled for more than 20hrs. Problem is after executing the jobs for 6 to 7 hrs the cron stops functioning. I need to reboot Sco Unix in order for the cron to be started. This is a serious problem for me as i need to take databases tran's log dumps every hour, and definately its wrong way to reboot the server for cron to be started. Waiting for an answer and thanx. Regards Nitin Nitin Shinde made comment on Fri Jul 25 09:53:24 2003 : > Hi, > I have a problem using cron on Compaq Proliant ML-370 O/S SCO 5.0.5.. > Jobs have been scheduled for more than 20hrs. Problem is after > executing the jobs for 6 to 7 hrs the cron stops functioning. I need > to reboot Sco Unix in order for the cron to be started. > This is a serious problem for me as i need to take databases tran's > log dumps every hour, and definately its wrong way to reboot the > server for cron to be started. > Waiting for an answer and thanx. What patches have been installed - specifically has the 'Cron Suppliment' oss642a been applied. -- ======================================================================== Tom Melvin tom@tkrh.demon.co.uk http://www.tkrh.demon.co.uk Veterinary Solutions Ltd Sysop Compuserve Unixforum ======================================================================== ...
SCO 5.0.5 dd / clone #2
Hi, I have an odd problem with one of my customer's SCO machines. Without going into a lot of detail and reasons for backup decisions, I have implemented a dd cloning of the master hard disk to a backup disk. That is to say my customer has 2 hard disks (in a caddy), the primary or master disk (hd00) and the clone or backup disk (hd10). A cron job wakes up twice daily and does a complete clone of the master disk to the backup / clone disk using dd. No great issue here as the entire disk (20Gb) takes about 24 minutes to complete. Now in Linux, this works great. If the master disk crashes for any reason, the customer simply re-boots their system and boots from the secondary drive whilst the primary is being repaired and all boots up fine and proper and no problems. However, the same process in SCO 5.0.5 seems to generate a completely corrupted disk. When I compare the master to the clone, you can see that the clone is completely a mess. I don't understand why this is the case with SCO but not with linux. As I'm doing a dd of the ENTIRE disk (a binary bit by bit copy), I don't understand why it doesn't work under sco. BTW - in SCO I don't boot from the secondary drive - I have to set it to the master drive first however, as per above the disk is so badly corrupted that the boot process will not work. The command I use is time dd if=/dev/hd00 of=/dev/hd10 bs=1451520 count=12529 (for SCO) time dd if=/dev/hda of=/dev/hdb bs=1451520 count=12529 (for l...
Problems with Business Basic on SCO 5.0.5
Hello, experts! I have an SCO Unix 5.0.5 server running Business Basic programs. When I try to connect my Wx PC clients to the Unix, via a Terminal Emulator, say Telnet or SCO TermLite in an ansi mode or vt100 mode, the Business Basic program interface appears to be "corrupted". It means that the sent characters look very untidy. So, I guess that the problem is with the bbx2 and not with the terminal emulator. I was seeking for some tips in this google group, and I just found that somebody put the following line in the .profile: stty rows 0 columns 0 xpixels 0 ypixels 0 Has anybody had a similar problem like mine? Many thanks! Rosa "Rosa2003" <rosa2003rosa@yahoo.com> wrote in message news:b2bd6daa.0308071139.5736a8e4@posting.google.com... > Hello, experts! > I have an SCO Unix 5.0.5 server running Business Basic programs. > When I try to connect my Wx PC clients to the Unix, via a Terminal > Emulator, say Telnet or SCO TermLite in an ansi mode or vt100 mode, > the Business Basic program interface appears to be "corrupted". It > means that the sent characters look very untidy. So, I guess that the > problem is with the bbx2 and not with the terminal emulator. I was > seeking for some tips in this google group, and I just found that > somebody put the following line in the .profile: > stty rows 0 columns 0 xpixels 0 ypixels 0 > > Has anybody had a similar problem like mine? > Many thanks!...
Trying to compile putty-0.60 on SCO UNIX 5.0.7 with GCC and SCO Dev
I am trying to compile putty downloaded from http://linux.softpedia.com/progDownload/PuTTY-Download-347.html but get the error below. gcc -g -O2 -Wall -Werror -DHAVE_CONFIG_H -DHAVE_X11 -DHAVE_X -DSYSV -Di386 -DS CO325 -D__SCO__ -DHAVE_XAW -DHAVE_SHAPE_EXT -DHAVE_SHAPE -DHAVE_SHM_EXT -DHAVE_X SHM -DHAVE_XCONVERTCASE -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr /include/atk-1.0 -I/usr/include/cairo -I/usr/include/pango-1.0 -I/usr/include/gl ib-2.0 -I/usr/lib/glib-2.0/include -I/usr/include/freetype2 -I/usr/X11R6/include -I.././ -I../charset/ -I../windows/ -I../unix/ -I../mac/ -I../macosx/ -c ../ proxy.c cc1: warnings being treated as errors .../proxy.c: In function `proxy_for_destination': .../proxy.c:315: warning: implicit declaration of function `strncasecmp' gmake: *** [proxy.o] Error 1 # My programming skill level tops out at ./configure and make. Searching for instances of strncasecmp in the putty working directory shows: /tmp/putty-0.60/unix # cd .. # find . -type f -print | xargs grep strncasecmp | less ../mac/stricmp.c:#define strncasecmp strnicmp ../mac/stricmp.c:strncasecmp(s1, s2, n) ../unix/unix.h:#define strnicmp strncasecmp (END) In unix/unix.h: #define DEFAULT_CODEPAGE 0xFFFF #define CP_UTF8 CS_UTF8 /* from libcharset */ #define strnicmp strncasecmp #define stricmp strcasecmp /* BSD-semantics version of signal(), and another helpful function */ void (*putty_signal(int sig, void (*func)(int)))(int); void block_si...
SYbase SQL & SCO OpenServer 5.0.4/5.0.5
Can somone help me with wich SQL versions runs on SCO OSR5.0.4 and SCO OSR 5.0.5? So your the customer SCO still has :-) Sorry.. Couldn't resist ! ASE 10.0.2 was certified on SCO OSR5.0.2 with OS patches SLS 422a, SLS 437a. It wasn't certified on anything higher. ASE 11.0.x was certified on 5.0.4, but nothing higher. Sybase doesn't support 10.x or 11.x any more ...
SCO's 5.0.7V on vmware server 2.0?
I see SCO has a downloadable 5.0.7 virtual machine in ISO form they boast will run on vmware, but the getting-started docs don't mention using vmware server 2.0 (the free version). Has anyone got this to work and if so how did you do it? It seems silly they don't document using it with the most popular versions of vmware. But it is SCO. And that yearly subscription? What were they thinking? That sure gives a lot of confidence--buying something that will quit on a yearly basis from a company that is going through bankruptcy. I am still using a 5.0.6 virtual machine I built three years ago for an old but required app, but it would be nice to go with something newer and better. OregonBob <oregonbob@gmail.com> wrote: > I see SCO has a downloadable 5.0.7 virtual machine in ISO form they > boast will run on vmware, but the getting-started docs don't mention > using vmware server 2.0 (the free version). Has anyone got this to > work and if so how did you do it? > > It seems silly they don't document using it with the most popular > versions of vmware. But it is SCO. (I worked at SCO for 15 years, and now VMware for 5 years; not speaking for either of them, of course...) As it turned out, VMware Server was never the most popular of VMware's products. It is now "end of life" (see small comment "*VMware Server was declared End Of Availability on January 2010. Support will be limited to Technical Guidance for the dura...
SCO Caldera v3.2.5.07 and Enterprise 5.0.7 3.2v5.0.7
I have 2 different software applications. We are considering moving both to a single server sunning sco. One vendor says they will only run on SCO caldera v 3.2.2.07 the other says they will only run on enterprise 5.0.7 3.2v5.0.7 I am confused, are these 2 different os's or just versions of the same os. Can someone enlighten me? gerard typed (on Fri, Oct 31, 2003 at 11:34:45AM -0800): | I have 2 different software applications. | We are considering moving both to a single server sunning sco. | One vendor says they will only run on SCO caldera v 3.2.2.07 There is no such version as 3.2.2.07. | the other says they will only run on enterprise 5.0.7 3.2v5.0.7 This is the latest release of SCO Openserver. -- JP gerardm@schurmans.com (gerard) wrote in message news:<97c6f92f.0310311134.2227a2c@posting.google.com>... > I have 2 different software applications. > We are considering moving both to a single server sunning sco. > One vendor says they will only run on SCO caldera v 3.2.2.07 > the other says they will only run on enterprise 5.0.7 3.2v5.0.7 > > I am confused, are these 2 different os's or just versions of the same os. > Can someone enlighten me? They both are the same, SCO UNIX 3.2V5.7 (enterprise). Abid ...
SCO 5.0.5/5.0.6 bios clock, time zone and synching
Hi All, Does SCO expect the BIOS clock to be set to UTC? Ive got a few SCO boxen spread across a couple of time zones and at the moment, the bios clocks in the servers are set to localtime not UTC. The timezone settings in SCO Admin are also wrong. I was under the impression *nix always expects the BIOS clock to be set to UTC and then the timezone settings in SCO tell the OS what the local time is. This does not seem to be the case for me. On a testing box, Ive set the BIOS clock to UTC, set the correct timezone in scoadmin but the date command in a root shell still gives the wrong time. Either the timezone information in scoadmin for my timezone is wrong and I need to set up an unlisted timezone (which I can do easily enough) or im missing something more fundamental here. Anyone care to wield a clue-bat? cheers John Smith wrote: > Does SCO expect the BIOS clock to be set to UTC? > > Ive got a few SCO boxen spread across a couple of time zones and at > the moment, the bios clocks in the servers are set to localtime not > UTC. > The timezone settings in SCO Admin are also wrong. > > I was under the impression *nix always expects the BIOS clock to be > set to UTC and then the timezone settings in SCO tell the OS what the > local time is. > This does not seem to be the case for me. > On a testing box, Ive set the BIOS clock to UTC, set the correct > timezone in scoadmin but the date command in a root shell still gives > the wro...
Using same SCO Openserver Enterprise 5.0.5. on 2 computers
Can I use the same SCO Openserver licence on two computers on the same network. I want to have a computer who is simply a clone of the other so I want to put the second computer on the network and make FTP transfert between the two computers. So if my "main" computer go down I can simply switch on the other computer. Thank you! "Mike" <michel.trudel@pentagone.com> wrote in message news:ede59572.0307291001.542e0fe0@posting.google.com... > Can I use the same SCO Openserver licence on two computers on the same > network. > I want to have a computer who is simply a clone of the other so I want > to put the second computer on the network and make FTP transfert > between the two computers. So if my "main" computer go down I can > simply switch on the other computer. > > Thank you! You'll get a repeated stream of console warnings from one or both machines that the same licenses are present on another machine on the network. These warnings will also be written to /usr/adm/syslog . Is this the only thing ? Is the syslog will be fill of those repeated messages or messages will appear once a day or something like that ? Is there any way to avoid those messages ? I've also heard that SCO can "stop running". Is there any "danger" ? Is there any lost of any functionnality ? Thanks! "Bob Bailin" <72027.3605@compuserve.com> wrote in message news:<bg8fhh$q81$2@ngspool-d02.news.a...
SCO 5.0.5 vs. 6.0
I'm having a new server built: SuperMicro P4SC8 Mother Board Intel P4 3.0Ghz 800 FSB 1GB CPU 73GB 10K 80 PIN SCSI Drive Sony 20/40GB DAT Drive SDT11000/BN DDS4 Adaptec 2010S Card for Mirroring Comtrol Rockport Card 99126-7 Is there any reason I should update my current version of SCO 5.0.5? Frank The following article is a recommendation from SCO when using P4 http://www.sco.com/ta/115963 "FrankS" <fshank@sbcglobal.net> wrote in message news:CqT_f.65026$H71.37215@newssvr13.news.prodigy.com... > I'm having a new server built: > > SuperMicro P4SC8 Mother Board > Intel P4 3.0Ghz 800 FSB 1GB CPU > 73GB 10K 80 PIN SCSI Drive > Sony 20/40GB DAT Drive SDT11000/BN DDS4 > > Adaptec 2010S Card for Mirroring > > Comtrol Rockport Card 99126-7 > > > > Is there any reason I should update my current version of SCO 5.0.5? > > > > Frank > > > > > > FrankS wrote: > I'm having a new server built: > > SuperMicro P4SC8 Mother Board > Intel P4 3.0Ghz 800 FSB 1GB CPU > 73GB 10K 80 PIN SCSI Drive > Sony 20/40GB DAT Drive SDT11000/BN DDS4 > > Adaptec 2010S Card for Mirroring > > Comtrol Rockport Card 99126-7 > > > > Is there any reason I should update my current version of SCO 5.0.5? Frank, OpenServer 5.0.5 is a retired product and is no longer generally supported by SCO. OpenServer 5.0.5 is not designed to work on P4 systems and y...
if time = 3 seconds, how do i set the values of the time steps 0,0.1,0.2,0.3,0.5,1.0,1.5,2.0,3.0,5.0 to -9999 from time =3 seconds
Hi I have 18 inputs (arrays) which contain certain statistics and if time = 3 seconds, set the values of time step 5.0 to -9999.0. I was wondering if there is an efficient way to do this without using a lot of case statements? Thank you. Hello AdrianT, it's not really clear to me what you want to do... I suspect: you have an array containing values and you want to output them with a fixed timing of 3 seconds: you should use a for loop autoindexing trough your array and sending the value to your indicator/output/whatever. Put a "wait for next multiple" into your for loop. Or do you want to have a minimum time delay of 3 seconds? Again use a for loop, get the time value and use a InRange&Coerce with minimum set to 3 seconds... Or you should explain more precisely what you need... Hi Thanks for that. Let me explain. The time may vary. Let me give an example. if time = 2.1, I want to set the time step's 3.0 and 5.0's values to -9999.0. if the time =0.1 seconds then I want to set 0.2,0.3, 0.5 etc values to -9999.0 etc .................................................................... Can you please help? Thank you. Hello TUDS, do you use different accounts/nicknames ? Well, that's easy, at least for a sorted array: Search for your time-value in the array (Threshold 1D array). Fill all elements from that index till the end with your "error...
Need NIC drivers/settings for SCO 5.0.5 on DELL pe2600
Hi All, An old customer that i dealt with many years ago called me saying = that their system had crashed and the people they were using were no help. = They did not have system backups but they had their DB backed up. I'm usi= ng their old dell server and their sco 5.0.5 disks and configured a new sys= tem. The one thing i can't find is NIC drivers. I have downloaded and ins= talled 2 sets of intel drivers but i have no idea what the card settings sh= ould be. After installing the drivers, running netconfig just gets me a li= st of cards i can select. any help would be greatly appreciated. thanks! On Friday, January 18, 2013 11:15:57 PM UTC-5, rdpcons...@gmail.com wrote: > Hi All, >=20 > An old customer that i dealt with many years ago called me sayin= g that their system had crashed and the people they were using were no help= .. They did not have system backups but they had their DB backed up. I'm u= sing their old dell server and their sco 5.0.5 disks and configured a new s= ystem. The one thing i can't find is NIC drivers. I have downloaded and i= nstalled 2 sets of intel drivers but i have no idea what the card settings = should be. After installing the drivers, running netconfig just gets me a = list of cards i can select. >=20 >=20 >=20 > any help would be greatly appreciated. >=20 > thanks! I ended up installing a 3com 3C905b and all is well. The intel driver i f...
Postgresql 7.4.1 Compile problem for SCO 5.0.5
I am trying to compile postgresql 7.4.1 for sco 5.0.5 and get the following error: "thread.c", line 269: error: undefined symbol: h_errno Any ideas? ../configure --with-libs=/usr/local/lib --with-includes=/usr/local/include herbie!/tmp/postgresql-7.4.1 # gmake gmake -C doc all gmake[1]: Entering directory `/tmp/postgresql-7.4.1/doc' gmake[1]: Nothing to be done for `all'. gmake[1]: Leaving directory `/tmp/postgresql-7.4.1/doc' gmake -C src all gmake[1]: Entering directory `/tmp/postgresql-7.4.1/src' gmake -C port all gmake[2]: Entering directory `/...
ttyp problem on Sco Open Server 5.04
I connect to my server trough a VT220 emulation PC and the server make a ttypX pseudo-terminal device. But when I logoff the emulation the server wrongly keep the ttypX without PID process. I sow this because when I shutdown the system It returned a message like "/etc/shutdown:3106 alarm call" and after 120 seconds it asked to me if I want to shutdown (y/n). The system then shutdown normally. Also the boot is correct and has no problems. What can I do to solve this problem? Thanks Marco This is the syslog file of my server with the telnetd error: [cut] Jul 9 08:43:56 scosysv telnetd[654]: ttloop: peer died: Unknown error Jul 9 08:44:22 scosysv telnetd[731]: ttloop: peer died: Unknown error Jul 9 08:44:42 scosysv telnetd[729]: ttloop: peer died: Unknown error Jul 9 08:45:17 scosysv telnetd[733]: can't find terminal control database entry for line ttyp0 Jul 9 08:46:43 scosysv telnetd[800]: can't find terminal control database entry for line ttyp0 Jul 9 08:49:28 scosysv telnetd[869]: can't find terminal control database entry for line ttyp1 Jul 9 08:50:03 scosysv telnetd[842]: can't find terminal control database entry for line ttyp0 Jul 9 09:57:19 scosysv telnetd[1084]: can't find terminal control database entry for line ttyp2 Jul 9 09:58:13 scosysv telnetd[1110]: can't find terminal control database entry for line ttyp2 Jul 9 10:00:50 scosysv telnetd[1056]: can't find terminal control database entry for line ttyp1 Jul 9 ...
SCO OpenServer 5.0.4/5.0.5 New Daylight Savings dates
Has anyone yet come up with a solution on changing older SCO OpenServer 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings dates starting this year?? I have looked around at SCO's site and they have an update to install on 5.0.7 systems that also indicate you should install new libc, etc Anyone know how to fix this on older SCO OpenServer releases?? Thanks for any help Scott Ullmann Telespectrum sullmann@telespectrum.com scooter typed (on Mon, Jan 22, 2007 at 12:37:58PM -0800): | Has anyone yet come up with a solution on changing older SCO OpenServer | 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings | dates starting this year?? | | I have looked around at SCO's site and they have an update to install | on 5.0.7 systems that also indicate you should install new libc, etc | | Anyone know how to fix this on older SCO OpenServer releases?? I'm in the EST timezone, and so I would edit /etc/TIMEZONE from: TZ=EST5EDT to: TZ=EST5EDT,M3,2,0/2,M11,1,0/2 -- JP ==> http://www.frappr.com/cusm <== On Jan 22, 4:24 pm, Jean-Pierre Radley <j...@jpr.com> wrote: > scooter typed (on Mon, Jan 22, 2007 at 12:37:58PM -0800): > | Has anyone yet come up with a solution on changing older SCO OpenServer > | 5.0.4 / 5.0.5 / 5.0.6 systems to accommodate the new daylight savings > | dates starting this year?? > | > | I have looked around at SCO's site and they have an update to install > | on 5.0.7 ...
3Com 3C905 XL PCI NIC on SCO 5.0.5 on Proliant 3000
hi there, following up on my install of Openserver 5.0.5 on a Compaq Proliant 3000, the only thing left to configre is the NIC. And I do this as follows: reboot boot up to X run network configuration manager add new LAN adapter choose 3Com Fast EtherLink XL PCI (3C905) When it asks for network driver configuration, i choose default (PCI bus:0, device:0, function:0) I presume this is ok, as it says '*' denotes conflict, and there is no * present. when asked to add protocol, i choose: SCO TCP/IP then add settings: machine name: propath ip: XX.XXX.XX.XX subnet mask: 255.255.0.0 broadcast mask: XX.255.255.255 domain name: mycompany.com tcp connections: 256 gateway: no advanced: gateway:no frame: ethernet-II i choose ok, save all. then am asked to relink kernel, i choose yes to all reboot machine(i know it is unnecessary to reboot but, i suppose its one of my windows hangups :)) and log on. run ifconfig -a and it gives me: lo atl0 (with various settings, including inet: 0.0.0.0) so there seems to be some prob;ems with the hardware. when i ping a known ip I get: no route to host any ideas? thanks in advance, bernard -- On 17 May 2004 12:50:20 GMT, bluNOboxSPAMthief <newsgroups-spambaiter@runningIHATEwithSPAMbulls.com> wrote: >hi there, > >following up on my install of Openserver >5.0.5 on a Compaq Proliant 3000, the only >thing left to configre is the NIC. > >And I do this as follows: > >reboot >boot up to X > &g...
Web resources about - 2 NICs problem in SCO Open Server 5.0.5 - comp.unix.sco.misc
Problem novel - Wikipedia, the free encyclopediaWorking class, or proletarian novels are often also social problem novels . This was in many ways a reaction to rapid industrialization , and ...
AFL Players' boss hits back at code's drug problems reportsExcerpts from 3AW host Neil Mitchell's extraordinary interview AFL Players Association CEO Paul Marsh amid allegations a quarter of Collingwood's ...
'Give us a chance' on football's drug problem says AFL Players Association CEO Paul Marsh... football's players' union says reporting of failed hair tests at Collingwood has set back efforts to deal with the sport's illicit drugs problem. ...
Rob Ford Lived The Gimmick, And That Was The Problem - Dan LytwynWhen someone we dislike passes away, we far too often revert to muted resignation. We purse our lips, dip our heads, and maybe mumble a few innocuous ...
Apple pulls iOS 9.3 update for older devices following activation problemsThe iPhone 4S and other older iDevices could be affected by this problem. (credit: Andrew Cunningham) Apple has temporarily pulled the iOS 9.3 ...
WaPo seems surprised that people regard yoga in school as an Establishment Clause problem.The headline is: "Ga. parents, offended by the ‘Far East religion’ of yoga, get ‘Namaste’ banned from school." In my opinion, it's cultural ...
One way to solve the problem of the pay gapOne way to solve the problem of the pay gap by digby Stop paying women and minorities less. Easy peasy: In an email to staff on Thursday, Wall ...
Mazda has 1 big problem — and 1 huge advantageMazda is one of those interesting small car brands in the US market: small but highly regarded. It has a very strong brand identity as a sort ...
Belgium attacks reinforce that security is everybody’s problem... Rob Enderle writes that it is more important than ever to rethink our security efforts. People seem to think security is someone else’s problem, ...
Obama: Climate Change Is a 'Major' Problem, But ISIS? 'They're Not An Existential Threat'
... on Wednesday. "They're not an existential threat to us," he said. But a few sentences later, he described climate change as a "major" problem. ...
... on Wednesday. "They're not an existential threat to us," he said. But a few sentences later, he described climate change as a "major" problem. ...
Resources last updated: 3/26/2016 1:17:35 PM