Hello,
Thanks for your time.
A ethernet link, called "ce1", has not the flag UP in the answer to
"ifconfig -a". Moreover, ping to own address fails.
"kstat" reports the link is up (link_up=1), and ifconfig gives valid
IP address, mask, ... . "netstat -i" reports packets incoming, but
none outgoing.
When a command "ifconfig ce1 up" is typed, the command doesn't says
nothing, nor finishes.
No messages in "var/adm/messages".
Please, any sugestion is welcome.
Thanks a lot.
|
|
0
|
|
|
|
Reply
|
tmp123 (184)
|
4/3/2007 1:02:04 PM |
|
tmp123 <tmp123@menta.net> wrote:
> Hello,
> Thanks for your time.
> A ethernet link, called "ce1", has not the flag UP in the answer to
> "ifconfig -a". Moreover, ping to own address fails.
Then you need to either bring it up manually (ifconfig ce1 up), and/or
fix the configuration for it in /etc/hostname.ce1
> "kstat" reports the link is up (link_up=1), and ifconfig gives valid
> IP address, mask, ... . "netstat -i" reports packets incoming, but
> none outgoing.
The link (ethernet) is up, but the IP configuration is not.
> When a command "ifconfig ce1 up" is typed, the command doesn't says
> nothing, nor finishes.
You mean it hangs forever?
What does 'truss ifconfig ce1 up' show as the last few lines?
--
Darren Dunham ddunham@taos.com
Senior Technical Consultant TAOS http://www.taos.com/
Got some Dr Pepper? San Francisco, CA bay area
< This line left intentionally blank to confuse you. >
|
|
0
|
|
|
|
Reply
|
Darren
|
4/3/2007 4:31:21 PM
|
|
Darren Dunham <ddunham@redwood.taos.com> writes:
> tmp123 <tmp123@menta.net> wrote:
> > When a command "ifconfig ce1 up" is typed, the command doesn't says
> > nothing, nor finishes.
>
> You mean it hangs forever?
>
> What does 'truss ifconfig ce1 up' show as the last few lines?
Even without seeing the truss output, that sounds like a system
problem. The original poster needs to contact support.
--
James Carlson, Solaris Networking <james.d.carlson@sun.com>
Sun Microsystems / 1 Network Drive 71.232W Vox +1 781 442 2084
MS UBUR02-212 / Burlington MA 01803-2757 42.496N Fax +1 781 442 1677
|
|
0
|
|
|
|
Reply
|
James
|
4/6/2007 12:56:30 PM
|
|
|
2 Replies
455 Views
(page loaded in 0.057 seconds)
Similiar Articles: ifconfig ce1 up: no answer - comp.unix.solarisHello, Thanks for your time. A ethernet link, called "ce1", has not the flag UP in the answer to "ifconfig -a". Moreover, ping to own address fails.... shows the duplicate in ifconfig - comp.unix.solarisbut now problem is when I do ifconfig -a ... the net, keep it simple and be back up within 10 minutes. Do a sys-unconfig and answer ... interface with another ip. ifconfig ce1 ... solaris 10 (Sparc) changing from dhcp to static ip??? - comp.unix ...But no qfe1 * okay, i have found this -> ifconfig qfe1 plumb up - well done, nothing happend * "ifconfig qfe1 ... Or not? > > > I don't use any zones so I can't answer ... how to get mac address of network interfaces - comp.unix.solaris ...In that case, the best answer is probably to do it the way ifconfig does: open the DLPI node (/dev/<name ... You could plumb it (but not set up a tcp address), find out the ... Interface IP address Change. - comp.protocols.time.ntpFor > these systems ntpd currently uses the periodic scan approach to pick up ... comp.unix.admin Hi Today I wanted to add 2nd interface with another ip. ifconfig ce1 plumb ... sys-unconfig - comp.unix.solarisI = have no=20 idea why, I never set them up that way. But I have some software that = took some ... You can't just ifconfig eri0 unplumb, etc. ? And in your /etc ... routing to two subnets over the same interface - comp.unix.solaris ...# ping 10.25.51.2 no answer from 10.25.51.2 # traceroute 10.25.51.2 ... 172.16.0.81/16 up Created new logical interface rtls0:2 % ifconfig -a lo0: flags=2001000849<UP ... ping using multiple interfaces - comp.unix.solaris... localhost UH 2 421 lo0 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING ... the same interface - comp.unix.solaris ... # ping 10.25.51.2 no answer ... showing same mac address for two NIC - comp.unix.solaris ...No problem; that's the default for SPARC ... I've done devfsadm and ifconfig ge0 plumb and it shows up as ge0. ... Answers... shows the general format of a MAC ... Linux driver (or help) needed for Atheros AR8151 Ethernet device ...(nomail.afraid.org has been set up specifically ... Then I ran "ifconfig -a", but still no eth0. Thoughts on this? ... needed for Atheros AR8151 Ethernet device - answer ... Cannot plumb interface ce1 'ifconfig: SIOCSLIFNAME for arp: ce1 ...ce0: flags=1000843<UP,BROADCAST ... @ Romeo ::/>ifconfig ce1 unplumb ifconfig: unplumb: SIOCGLIFFLAGS: ce1: no such interface ... Get Answers - It's Free Solaris Operating System: ifconfig: solaris 10: new restrictions ...ifconfig from progam; ifconfig fails to configure second network card at boot; ifconfig ce1 up: no answer; ifconfig causes libdlpi.so.1 error; Hi,I had a question about ifconfig. 7/27/2012 12:09:24 AM
|